|
Q1. You are upgrading your server hardware. On a 486
computer you want to take out some interface cards and put them onto your
Pentium 2 based server. What type of interface devices should be suitable?
(Choose 2)
A. ISA
B. PCI
C. PCI X
D. VLB
E. MCA
F. AGP
ANSWER: A & B
Q2. You are configuring the SCSI hardware on your server. What SCSI
configuration allows for 16-bit bus and a data rate of 80 MBps?
A. Wide Ultra2 SCSI
B. Ultra2 SCSI
C. Ultra3 SCSI
D. Wide Ultra SCSI
E. SCSI 2
ANSWER: A
Q3. You are configuring the SCSI hardware on your server. You are considering
to deploy SCSI 3 devices. Which of the following
correctly describe SCSI 3? (Choose all that apply)
A. 32bit bus
B. 16bit bus
C. 20MB/S
D. 40MB/S
E. 60MB/S
F. also known as Ultra Wide SCSI
G. also known as Ultra SCSI-2.
ANSWER: B, D & F
Q4. You are troubleshooting your server hardware. Your assistant reports the
following symptoms:
He can hear noises and see lights on the computer box. However, nothing shows
on the screen.
What is the likely problem? (Choose all that apply)
A. Video card
B. Monitor
C. Hard drive
D. Motherboard
E. CPU
ANSWER: A & B
Q5. You need to setup your server so that the risk of component failure is
minimized. Which of the following is a recommended action?
A. regularly clean the inside of the server
B. regularly clean the outside of the server
C. regularly run scandisk
D. deploy UPS
E. deploy RAID
F. None of the choices.
ANSWER: A
Q6. You are configuring the server display. The server uses a display card
that has 32MB of video RAM built in. Which of the following resolution and
color combinations are achievable? (Choose all that apply)
A. 1024 x 768 at 24-bit color
B. 1280 x 1024 at 32-bit color
C. 1600 x 1024 at 32-bit color
D. 1024 into 768 at 64-bit color
ANSWER: A, B, C & D
Q7. When you upgrade your server you find out that the motherboard only
supports one type of memory at a time. That means:
A. all ram chips must be of the same make
B. all ram chips must be of the same standard, like DIMM or SIMM
C. all ram chips must be of the same capacity
D. all ram chips must be of the same size
ANSWER: B
Q8. You just installed a second IDE slave hard drive to the primary
controller of your server. When you boot it up via a DOS disk, you can access
the drive letter D. When you try to run the DIR command against it, you
receive an error. Why?
A. Your hard drive is not partitioned.
B. Your hard drive is not formatted.
C. Your hard drive is not detected.
D. Your hard drive has no IRQ assigned.
E. Failed controller
F. Failed terminator
ANSWER: B
Q9. You are inspecting your x86 based server. This server has a Centronics (36-pin) D-shell connector at the back. You
may use this connector to support what device?
A. parallel printer
B. serial printer
C. network printer
D. SCSI device
E. IDE device
F. external drive
ANSWER: A
Q10. You are inspecting your file server's network connection. To connect
this server to another server directly without going through a hub, you
should use:
A. A crossover cable
B. A server to server 68 pin cord
C. A server to server 40 pin cord
D. A regular cat 3 patch cord
E. None of the choices.
ANSWER: A
Q11. Your file server is running Windows 2000. The drive is running close to
being out of space. What should you do other than to purchase an additional
drive?
A. Enable quota management
B. Enable drive caching
C. Use DriveSpace application
D. Use a smaller swap file
ANSWER: A
Q12. You want to give your server more horse power. The system currently uses
a Pentium 100 CPU. Which of the following CPUs can you use to upgrade this
server?
A. a Pentium MMX 233
B. a Celeron 300
C. a P II 400
D. a P III 600
E. a MediaGX 233
F. None of the choices.
ANSWER: A
Q13. You are configuring your server. You install Windows 2000 on it and plan
to have it functions in a peer to peer environment. Which of the following is
appropriate to use?
A. Domain
B. Active Directory
C. Context
D. Workgroup
E. None of the choices.
ANSWER: D
Q14. On your network there are four and only four computers. You designate
all of them as servers. Which of the following correctly describe the type of
network you are configuring?
A. peer to peer
B. client server
C. centralized
D. decentralized
E. None of the choices.
ANSWER: A
Q15. Your X86 server deploys a CPU architecture that combines the CPU and the
L2 Cache together into a chip. This describes:
A. SEC
B. SMP
C. 423
D. 478
E. 370
F. ZIF
ANSWER: A
Q16. You are configuring the server's system bios. Which of the following are
terms related to your hard drive? (Choose all that apply)
A. Heads
B. Sectors
C. Cylinders
D. Cache
E. Pre-fetch
ANSWER: A, B & C
Q17. You are planning for a list of the server hardware components to be
used. Which of the following devices is supported ONLY by SCSI but NOT by
IDE?
A. CD-ROM
B. Hard Drives
C. Scanner
D. Printer
E. Mouse
F. None of the choices.
ANSWER: C
Q18. You want to configure your server to be connected with a fiber optic
network. Which of the following connectors are appropriate for your NIC?
(Choose all that apply)
A. ST
B. SC
C. JE
D. DTE
E. DCE
ANSWER: A & B
Q19. You are configuring your server devices. Which of the following devices
requires a configuration utility to be used for installation?
A. jumperless
B. PCI
C. IEEE compliant
D. OSI complaint
E. Firewire
F. PC 99
ANSWER: A
Q20. You are configuring your server to accept RAS phone call. Which of the
following actions will render the modem configuration non-functional?
A. plug the phone line into the phone port of your modem card
B. plug the phone line into the line port of your modem card
C. use an internal modem that supports up to 28.8kbps
D. use an external modem that supports up to 56kbps
E. apply the latest server OS patch
ANSWER: A
Q21. You need to setup your server so that the risk of component failure is
minimized. The server is to be run on a 24x7 basis. In order to minimize the
risk of component failure, which of the following actions should you take?
A. ensure better system cooling
B. regularly clean the outside of the computer
C. regularly run scandisk
D. deploy UPS
E. deploy RAID
F. None of the choices.
ANSWER: A
Q22. You are considering to deploy multiple USB
devices on your Windows 2000 server. To do so, you buy couple of USB hubs.
Before you connect the 8 USB devices on your computer, as a minimum how many
IRQ should you free up?
A. 0
B. 1
C. 4
D. 8
E. 2
F. None of the choices.
ANSWER: B
Q23. You are configuring the SCSI hardware on your server. The ability to
configure each SCSI device with a unique identification number is for what
purpose?
A. higher throughput
B. lower down time
C. lower cost
D. attaching multiple SCSI devices to the same channel
E. attaching multiple SCSI devices to different motherboards
ANSWER: D
Q24. You want to give your server the ability to write data into CD Discs for
backup purposes. You purchase an internal IDE CD Writer. For it to work, you
should:
A. check the jumper setting on the CD writer during installation
B. check the cache size setting on the CD writer during installation
C. use a terminator appropriately
D. set the SCSI chain ID appropriately
E. check the cylinder setting on the CD writer during installation
F. check the power supply on the chassis during installation
ANSWER: A
Q25. What memory address range is likely to be used by your server's Matrox display adaptor?
A. C000-C7FF
B. F000-C6FF
C. A000-B1FF
D. FFFF-C7FF
E. None of the choices.
ANSWER: A
Q26. You need to edit the boot.ini file of your Windows 2000 server system.
What tool can you use to do so?
A. Notepad
B. Regedit
C. Regedt32
D. DrWatson
E. System File Checker
F. None of the choices.
ANSWER: A
Q27. The smallest storage access unit on your server's 20GB
SCSI 2 hard drive is:
A. a sector
B. a buffer
C. a track
D. a record
E. a KBPS
ANSWER: A
Q28. You are configuring your newly purchased Windows 2000 Server computer.
You need to configure the device drivers. What drivers are are binary-compatible with Windows 2000 and Windows 98?
A. NT device drivers
B. WDM device drivers
C. HCL device drivers
D. ACL drivers
E. None of the choices.
ANSWER: B
Q29. What feature of Windows 2000 server allows the remote monitoring of
application software?
A. Terminal Service
B. Administration Checkpoint
C. Service Anywhere
D. Site Management Service
E. None of the choices.
ANSWER: A
Q30. You need to purchase an extinguisher for your server room. What class of
extinguisher is more appropriate?
A. Class A
B. Class B
C. Class C
D. Class D
ANSWER: C
Q31. You are planning a backup scheme for your file server. Which of the
following backup methods takes the longest time to complete?
A. differential
B. incremental
C. full
D. weekly
ANSWER: C
Q32. You are upgrading your server hardware. On a Pentium III motherboard, it
is likely for you to find multiple instances of which of the following BUS
slots? (Choose all that apply)
A. ISA
B. PCI
C. VLB
D. AGP
ANSWER: A & B
Q33. You are configuring the server display. For some reason the screen goes
blank, although the server is running. Which of the following is a likely
cause?
A. you set the display adaptor's refresh rate to a level that is too high
B. you set the display adaptor's refresh rate to a level that is too low
C. you set the display adaptor's refresh rate to a level that is zero
D. you set the display adaptor's RAM amount to 2MB
E. you set the display adaptor's RAM amount to 512K
ANSWER: A
Q34. On your X86 based server, which of the following components are
considered as ROM related? (Choose all that apply)
A. BIOS
B. POST
C. CMOS
D. SDRAM
E. L2 cache
ANSWER: A, B & C
Q35. You are configuring your X86 server. Which of the following components
in the server are equipped with BIOS? (Choose all that apply)
A. Video card
B. SCSI card
C. IDE card
D. LPT card
E. RAM card
ANSWER: A & B
Q36. You are configuring your server. You want to instruct your computer not
to try booting from the floppy drive. Which of the following is a valid
action to take?
A. Configure the boot sequence in the BIOS
B. Configure the boot sequence in the OS
C. unplug the floppy's cable
D. unplug the floppy's power cord
E. remove the floppy disk from the drive
ANSWER: A
Q37. You need to replace your server motherboard. Why would you prefer an ATX
board over an AT board, if Windows 2000 is the OS of your choice?
A. higher performance
B. cooler temperature
C. on board NIC
D. higher reliability
E. shutdown via software
F. auto UPS fallback
ANSWER: E
Q38.
You want to configure your server BIOS, but it is locked with a password. You
do not know the password. What is the easiest way to fix this?
A. temporarily remove the CMOS battery
B. replace the BIOS
C. flash the BIOS
D. replace the motherboard
ANSWER: A
Q39. What command do you use to get rid of a corrupted boot sector on your
x86 based server drive?
A. fdisk /mbr
B. scandisk
C. chkdsk /f
D. ndd
E. None of the choices.
ANSWER: A
Q40. You are configuring your server devices. You need to configure the IRQs. What IRQ is used by the system timer?
A. 0
B. 1
C. 2
D. 5
E. 8
F. 10
G. 11
ANSWER: A
Q41. When you need to attach multiple IDE drives to your server, what
settings are particularly important?
A. master/slave jumpers
B. device ID
C. terminators
D. cable pinouts
E. None of the choices.
ANSWER: A
Q42. On your X86 base print server, which of the following components
requires DMA to be set?
A. EPP
B. ECP
C. Serial
D. RS 232
E. Fiber optics
ANSWER: B
Q43. The failure of hardware detection on your newly setup file server based
on the x86 architecture is likely caused by?
A. IRQ conflicts
B. failed BIOS battery
C. mis-configured motherboard jumpers
D. hardware listed in HCL
ANSWER: A
Q44. You want to deploy IDE drives for your new server. What standard
delivers a throughput of 66 MBPS?
A. Fast ATA
B. ATA2
C. Ultra ATA
D. ATA 66
E. None of the choices.
ANSWER: D
Q45. Users complain that they all fail to connect to the server. The server
is functioning properly. Which of the following may be a valid cause? (Choose
all that apply)
A. Bad patch cable
B. Bad passwords
C. Bad user names
D. Bad hub
ANSWER: A & D
Q46. An error that indicates Bad or missing operating system at boot up
means:
A. there is a corrupted boot sector
B. there is a windows protection fault
C. there is an illegal operations
D. there is a memory leak
E. None of the choices.
ANSWER: A
Q47. You are configuring your server to act as a print server. John prints a
Word document from his workstation. A page with bunch of printer code is
produced. What is the likely cause?
A. a wrong printer driver
B. bad print head
C. bad print server memory
D. memory leak
E. None of the choices.
ANSWER: A
Q48. You need to upgrade your server 's processor.
Your server has been using a Celeron 233 processor. Which of the following
processors is a valid upgrade choice?
A. Pentium III 800
B. Pentium II 333
C. Celeron 266
D. K7 500
E. None of the choices.
ANSWER: B
Q49. You just finished replacing the floppy drive on your server. For some
reasons the floppy drive has its light on continuously since system start up.
What is wrong?
A. improper floppy drive cable connection
B. missing power cord for the floppy drive
C. bad floppy motor
D. BIOS error
E. None of the choices.
ANSWER: A
Q50. Your server has been using a 400 mhz Celeron
processor. You want to upgrade it without replacing the motherboard. Which of
the following processor should you choose?
A. AMD Athlon 1.1G
B. AMD Duron 900MHZ
C. P4 1.5G
D. P2 500MHZ
E. None of the choices.
ANSWER: D
Q51. On which type of server system is CPU load balancing made possible?
A. SMP
B. RAID
C. Firewire
D. PLP
E. SNMP
ANSWER: A
Q52. You are configuring your newly purchased Windows 2000 Server computer.
You need to configure the device drivers. What option prevents invalid
drivers from causing damages to your system?
A. driver signing
B. driver endorsement
C. system checking
D. system maintenance
E. None of the choices.
ANSWER: A
Q53. Your newly purchased server uses a processor that requires memory chips
running at 266mhz. Which of the following types of memory can you use?
(Choose all that apply)
A. DDR
B. SDRAM
C. EDO
D. FPM
E. SIMM
ANSWER: A
Q54. Your server includes support for IEEE 1394. This standard supports
devices that are:
A. used internally
B. used externally
C. used securely
D. used for space saving
E. None of the choices.
ANSWER: B
Q55. On your Windows 2000 Server, what tool do you use to end an application?
A. Task Manager
B. System File Checker
C. Recovery console
D. Active Directory Wizard
ANSWER: A
Q56. What causes computer lights flicker on an x86 SMP system?
A. Electrical sag
B. Bad display card
C. Memory leak
D. OS error
E. Missing driver
F. None of the choices.
ANSWER: A
Q57. Your server includes support for IEEE 1394. With this standard, what is
the max throughput?
A. 133 mbps
B. 233 mbps
C. 266 mbps
D. 400 mbps
E. 500 mbps
F. None of the choices.
ANSWER: D
Q58. You are upgrading your server hardware. On a Pentium motherboard, what
type of interface devices can be deployed? (Choose 2)
A. ISA
B. PCI
C. PCI 64
D. VLB
E. MCA
ANSWER: A & B
Q59. You need to choose an OS for your server. This server is SMP based.
Which of the following OSes is NOT appropriate?
(Choose all that apply)
A. Unix
B. Linux
C. Windows 2000
D. Windows NT
E. Windows ME
F. None of the choices.
ANSWER: E
Q60.
Your server includes support for IEEE 1394. This standard has an advantage
of:
A. faster data transfer rates
B. better compatibility
C. higher cost
D. lower TCO
E. energy saving
F. None of the choices.
ANSWER: A
Q61. On a Windows 2000 server, what interface do you use to remove an
interface card as well as its software driver?
A. Device Manager snap-in
B. admintool
C. Server Manager
D. Active Directory Wizard
E. None of the choices.
ANSWER: A
Q62. Your file server is running Windows 2000. The drive is running close to
being out of space. You want to deploy disk quotas. Currently the server is
using only FAT32 partitions. What command / utility should you use first on
the drive before quota can be assigned?
A. convert
B. System File Checker
C. Recovery console
D. Active Directory Wizard
E. DriveSpace application
ANSWER: A
Q63. For your multi-boot server system to accommodate NT, Windows 98 and
Windows 2000, you should format your C drive as:
A. NTFS
B. FAT
C. FAT32
D. CDFS
E. None of the choices.
ANSWER: B
Q64. Multi-threading is made possible with what type of server configuration?
(Choose all that apply)
A. SMP system with two processors
B. SMP system with one processor
C. PnP system with two processors
D. SCSI system with one processor
E. None of the choices.
ANSWER: A
Q65. Which of the following is an example of POST error?
A. floppy drive error
B. bad sector error
C. data read error
D. illegal operation error
E. None of the choices.
ANSWER: A
Q66. On your Windows 2000 server there are multiple drives. You want to
configure these drives to run as RAID 5. To do so, these drives must be
converted to:
A. dynamic disks
B. NTFS
C. NTFS version 4
D. mirror
E. drive volume
F. None of the choices.
ANSWER: A
Q67. You are configuring the disk subsystem of your P3 server. A motherboard
for Pentium III, in general, support how many primary drives without the need
to install separate controller card?
A. one
B. two
C. three
D. four
E. None of the choices.
ANSWER: B
Q68. You need to ensure that your server is not affected by interrupted power
supply. Which of the following UPS types provide constant power to your
server?
A. Online UPS
B. SPS
C. Invert UPS
D. Fault Tolerant UPS
E. None of the choices.
ANSWER: A
Q69. You want your server to run SMP for higher performance. Which of the
following processors can you use for SMP at a speed faster than 700MHZ?
(Choose all that apply)
A. Pentium
B. Pentium II
C. Pentium III
D. K7
E. Celeron
ANSWER: C
Q70. Your server includes support for IEEE 1394. With this standard, your
server can support how many devices?
A. 13
B. 39
C. 94
D. 63
E. None of the choices.
ANSWER: D
Q71. Your Windows 2000 server is infected with a boot virus. What should you
do to fix the problem?
A. emergency repair process
B. reinstallation
C. in place upgrade
D. fdisk
E. None of the choices.
ANSWER: A
Q72. You need to replace your motherboard with a new one. When you purchase a
motherboard without on board cache, what type of processors should you
consider without compromising performance? (Choose all that apply)
A. Pentium
B. Pentium II
C. Pentium III
D. Pentium II Xeon
E. Pentium 4
ANSWER: B, C, D & E
Q73. You have clients that run desktop applications which require the 3D Now
instruction set. Which of the following processors should you use for the
server? (Choose all that apply)
A. AMD Athlon
B. AMD Duron
C. Pentium 2
D. Celeron
ANSWER: A, B, C & D
Q74. On your X86 server, Windows 2000 could not start because NTOSKRNL.EXE is
missing. What should you do to resolve the problem?
A. use the Recovery Console
B. run the Safe Mode Repair process
C. run the System File Checker.
D. Edit the BOOT.INI from DOS
ANSWER: A
Q75. Your file server is running Windows 2000. The drive is running close to
being out of space. To enable disk quota, what file system must be deployed?
(Choose all that apply)
A. NTFS
B. CDFS
C. FAT32
D. FAT
E. None of the choices.
ANSWER: A
Q76. Your Windows 2000 Server is taking longer than usual to access the hard
disk. What should you do to fix the problem without involving additional cost
if possible?
A. Enlarge the SWAP file size
B. Adding more RAMs to the server
C. Run scandisk
D. Run Disk Defragmenter
E. Run System Monitor
ANSWER: D
Q77. You plan to install Windows 2000 in a dual-boot configuration on your
server computer. Your computer has 2 drives. Drive 1 holds the systems, while
drive 2 holds the data. For maximum compatibility, what file system should
you use for the data drive?
A. FAT
B. NTFS
C. NFS
D. EFS
E. None of the choices.
ANSWER: A
Q78. You are configuring your Windows 2000 server. Fault tolerance of the OS
is critical. Which of the following should you deploy? (Choose all that
apply)
A. Software RAID 1
B. Software RAID 5
C. Hardware RAID 1
D. Hardware RAID 5
ANSWER: A, C & D
Q79. You edit the registry of your Windows 2000 Server computer. You restart
the computer, but the computer stops responding before the logon screen
appears. How do you return the server computer to its previous configuration?
A. Recovery Console
B. Fixboot
C. Last known good configuration
D. VGA mode
E. Safe mode
F. None of the choices.
ANSWER: C
Q80. You suspect that your server's E drive which is a data drive contains
bad sectors. What tools can you use to identify the problem?
A. scandisk
B. fdisk
C. chkdsk
D. diskscan
E. None of the choices.
ANSWER: Answer is A
Q1. A technician wants to ensure that a memory upgrade package that has
arrived is compatible with the server's motherboard. Where is the best place
to find the information?
A. The RAM manufacturer
B. The motherboard manual
C. The OS manual
D. The CPU manufacturer
ANSWER: B
Q2. You are planning to implement software RAID in the Windows NT
environment. Which of the following software RAID levels does this
environment not support?
A. Level 1
B. Level 5
C. Level 3
D. Level 0
ANSWER: C
Q3. A network administrator uses an incremental backup plan. A user requires
an entire directory tree restored from the day before. Only certain files
have changed during the week, but the entire directory was accidentally
deleted. What tapes will be needed to complete the restore?
A. The last differential tape
B. The last full backup tape
C. The last incremental tape
D. The last full backup tape, plus every incremental tape up to the day of
deletion
ANSWER: D
Q4. When troubleshooting the failure of a hard disk drive within a RAID
array, what should be the first step in attempting to recover the array?
A. Break the mirror
B. Check the backup of the system
C. Find out the RAID level
D. Check if the drive is SCSI or IDE
ANSWER: C
Q5. Consider the following statements:
Statement 1: The DMA feature of a bus allows devices to bypass the processor
and write their information directly into main memory.
Statement 2: The bus-mastering feature of a bus allows a device to read or
write directly to another device bypassing the CPU.
Which of the following is true about these statements?
A. Both statements are false.
B. Only statement 1 is true.
C. Only statement 2 is true.
D. Both statements are true.
ANSWER: D
Q6. A customer is complaining that their database server's performance is
very slow. When the server is monitored, all indicators are normal, but disk
utilization is revealed to be very high. What problem could this indicate?
A. Not enough RAM
B. Processor is too slow
C. Not enough disk space
D. Network card is defective
ANSWER: A
Q7. You decide to use the ATA-33, also called the Ultra DMA, standard in your
computer. Which of the following points should you keep in mind about this
standard?
A. The Ultra DMA mode should be enabled on the drive.
B. The controller must support Ultra DMA.
C. The system BIOS and/or operating system must support Ultra DMA.
D. All of the above.
ANSWER: D
Q8. You upgraded the Network OS on a server, and as a result some of the
hardware on the system stops working. How should you resolve this problem?
A. Install latest hardware drivers specific to the
OS
B. Consult OS, and hardware documentation, websites, and so on
C. Reinstall previous version of Network OS
D. Purchase newer hardware
ANSWER: A
Q9. A technician is concerned about the poor power quality in the company's
building. What device can the technician use to ensure that the servers are
receiving good power?
A. Line Conditioner
B. Power Bar with circuit breaker
C. UPS
D. Surge Suppressor
ANSWER: A
Q10. A server has just been connected to a new UPS. When the technician pulls
the power plug to test the UPS, both the UPS and the server abruptly shut
down. What is the most likely cause of the UPS not running from battery?
A. The server BIOS was not updated
B. The UPS software was not installed
C. The serial cable to the server was disconnected
D. The UPS battery was not charged
ANSWER: D
Q11. A technician wants to keep track of any application errors that happen
on a newly installed mail server. What should be enabled to monitor these
errors?
A. Performance Monitor
B. Event logs
C. Network monitor
D. Screenshot
ANSWER: B
Q12. What type of SCIS signaling solves the incompatibility issues of SE and
HVD?
A. Low Voltage Differential
B. Mid Voltage Differential
C. Multi-Differential Signaling
D. Low/High Voltage Differential
ANSWER: A
Q13. A server in the company's remote Houston office crashed on the weekend,
and the error message was not noticed until late Monday morning when the
administrator entered the computer room. How could this situation been
resolved more efficiently?
A. Visit the office over the weekend to make sure the server is running
B. Configure remote notification to page IS staff when there is a problem
with the servers
C. Dial into the office from home and monitor the servers remotely
D. Install a SNMP monitoring agent
ANSWER: B
Q14. A network card has just been installed into a server. When the server is
rebooted, the technician notes during the startup that the network card is
conflicting with the IRQ address of a sound card in the system. What should
be done to fix the problem?
A. Move the network card to another slot
B. Update the BIOS
C. Remove the sound card
D. Change the DMA of the network card
ANSWER: C
Q15. Your computer had an IDE hard drive. You replaced the hard drive with a
Single Ended SCSI system to improve his computer's performance. The total
length of cables used in the SCSI system is approximately 8 meters. However,
you find that after the installation of the SCSI system, the peripherals have
stopped responding. What could be the possible reasons? (Choose all that
apply.)
A. There is an improper cable insertion.
B. Single Ended SCSI systems use an unbalanced electrical signal.
C. The cable length is less than the minimum allowed cable length.
D. Single Ended SCSI systems do not work if the total length of their cables
exceeds 6 meters.
ANSWER: A & D
Q16. Consider the statements given below:
Statement 1: DMI is an API that software can use to gather information about
a computer's environment.
Statement 2: DMI depends on the platform and the operating system that a
computer uses.
Which of the following statements is true about these statements?
A. Only statement 1 is true.
B. Only statement 2 is true.
C. Both statements are true.
D. Both statements are false.
ANSWER: A
Q17. AeroWorks Airways has hired you to computerize
its flight inquiry system. The Airways uses a database that contains details,
such as the departure time, arrival time, number of seats available, and the
fare. Which SCSI system should you implement to enable fast data access?
A. Wide Ultra-2 SCSI
B. Ultra-3 SCSI
C. SCSI-2 "Fast"
D. SCSI-2 "Wide"
ANSWER: B
Q18. You have just finished upgrading your UPS with a newer model, and you
have installed a signal cable that connects the server to the UPS. For some
reason the server will not communicate with the UPS. What might be the cause
of this?
A. The UPS software is not configured properly
B. The batteries are not charged
C. The UPS is not compatible with the Server OS
D. The UPS is not plugged in.
ANSWER: A
Q19. How would you terminate an internal 8-bit SCSI device on an Ultra2 bus?
A. Terminate the 8-bit device anywhere on the bus
B. Place the 8-bit device anywhere along the bus, and
terminate it with a 16-bit device
C. Terminate the last 16-bit device, and the 8-bit device.
D. Terminate the bus using the last 16-bit device
ANSWER: B
Q20. At what point in your server installation should you develop a disaster
recovery plan?
A. Before the installation
B. After the first disaster
C. When the installation is completed
D. When purchasing your backup tapes
ANSWER: A
Q21. A customer wishes to implement a software RAID solution on their server.
What must be present to implement this system?
A. Hot swap disk drives
B. An embedded RAID controller
C. Enough CPU power and RAM to power the system
D. An external RAID storage system
ANSWER: C
Q22. Your database server is behaving odd, and you often have to reboot it
because the applications continue to crash. In order to resolve this problem,
what should you check first?
A. Memory
B. Log files
C. Hard drive capacity
D. Network bandwidth
ANSWER: B
Q23. A technician is scheduled to perform a BIOS upgrade to a newly installed
database server. What is the best resource for acquiring the most recent BIOS
files?
A. Third party vendor
B. Network OS installation media
C. Network OS vendor's website
D. System manufacturer's website
ANSWER: D
Q24. In Ethernet architecture, what does 100BaseTX represent?
A. The network uses coaxial cabling and has a data transfer rate up to 100
mbps.
B. The network uses fiber-optic cabling and has a data transfer rate up to
100 mbps.
C. The network uses fiber-optic cabling and has a data transfer rate, which
is about 100 times faster than that supported by token ring.
D. The network uses high-quality twisted-pair cabling and has a data transfer
rate up to 100 mbps.
ANSWER: D
Q25. You are the network administrator of your company. The company has its
head office in San Francisco and branch offices in Los Angeles and Denver. The company plans to open
another branch office in Dallas. You have been assigned the
responsibility of planning and implementing the hardware requirements of the
servers and other computers for the branch office. Your first task is to
decide the hardware to be used for the computers. Which of the following
architecture would you use for the optimum performance of the CPU?
A. AGP
B. PCI Bus Mastering
C. Hierarchical PCI Bus
D. Peer PCI Bus
ANSWER: B
Q26. How would you display the current TCP/IP network connects in Windows NT?
A. NETSTART
B. NTNETST
C. ARP
D. NETSTAT
ANSWER: D
Q27. You are working on a server installing a new piece of hardware. What
precautions should you take to prevent ESD?
A. Use conductive furniture
B. Maintain proper humidity levels
C. Where a grounded wrist strap
D. Wear a wool shirt
ANSWER: A, B & C
Q28. Your hard drive is using ATA technology capable of 33 Mbps transfer
rate. What ATA technology is it using?
A. ATA 3
B. ATA 3OO
C. ATA 33
D. DMA mode 3
ANSWER: C
Q29. A new processor has just arrived to be added to an existing server. What
should the technician verify before proceeding with the installation?
A. Brand Name
B. Cache
C. Stepping
D. Speed
ANSWER: C
Q30. You decide to implement a SCSI-1 solution on your computer, which is
running the Windows NT operating system, to facilitate faster data recovery.
You plan to add two internal hard drives. What SCSI IDs should you assign to
these hard drives?
A. Assign 7 to the boot drive and 6 to the second drive
B. Assign any two unique IDs from 0 to 7
C. Assign 0 to the boot drive and 1 to the second drive
D. Assign 1 to the boot drive and 0 to the second drive
ANSWER: C
Q31. A user is complaining that there is a loud buzzing noise coming from the
server. What is most likely to be the problem?
A. CPU fan
B. Network Card
C. Video Monitor
D. SCSI Adapter
ANSWER: A
Q32. You have just finished setting the IP network configuration on a newly
installed server. You can ping the IP address of the NIC, but cannot ping any
other devices on the LAN. You have verified that the NIC, cable, and the port
in the switch are functioning, and that there are link lights at both ends.
You can also ping the server from your own workstation. What is most likely
the problem?
A. Incorrect IP configuration
B. Bad NIC
C. Port in the switch is not set to Auto Negotiate
D. Damaged cabling
ANSWER: A
Q33. Consider the following statements:
Statement 1: The SNMP protocol is based on the Manager/Agent paradigm of
network management.
Statement 2: The SNMP protocol retrieves and modifies the information stored
in the Management Information Base (MIB), which is a virtual information
database that defines the properties of the managed object within the device
to be managed.
Which of the following is true about these statements?
A. Only statement 2 is true.
B. Both statements are true.
C. Only statement 1 is true.
D. Both statements are false.
ANSWER: B
Q34. At exactly 12 noon each day, there are complaints from the users
that an internal web server is very slow. What should be checked to ensure
that performance is normal throughout the day?
A. RAM usage
B. Examine event logs for the presence of maintenance programs
C. User's work habits during that time
D. Network analysis
ANSWER: B
Q35. MiSem Inc. is a marketing research company.
The company has approximately 2700 employees who need Internet access.
Currently, the company is using a dial-up connection. However, it has been
observed that the access speed is slow and that the employees have been
accessing undesirable sites.
As a network administrator, which server do you need to install to improve
the access speed and restrict the employees from visiting undesirable sites?
A. Firewall server
B. DHCP sever
C. Web server
D. Proxy server
ANSWER: A
|
|