I2C Bus FAQ Version 3.0
(c) 1995-2000 V.Himpe


This article is a collection of information sources on the I2C Bus. The document exists as a HTML file and as a iSilo document for Palm (tm) based organisers. You are free to use , copy , distribute and disclose the contents of this faq to anyone provided no money is asked for the copy.

Use of information in this faq is solely at the users risk. No liability will be accepted for any damage or loss resulting from the use or abuse of information contained in this document.

I2C Bus FAQ Version 3.0

Preface
About his Faq
Who Put it together
How can i contribute to it
Where will it be posted ?
May I distribute this FAQ or post it somewhere else?
ABOUT I2C
Historical background
I2C Bus protocol
Bus Hardware
Events on the I2C Bus
Start and Stop conditions
Putting something on the bus.
Addressing a SLAVE chip.
Waiting for Acknowledge
What happens next ?
Writing one or more bytes to a SLAVE.
Reading one or more bytes from a SLAVE.
Determining the SLAVE access mode.
Combined data format
MultiMASTER operation
Bus synchronisation mechanism
Special addresses and exceptions
Some general notes about reserved addresses.
Electrical specs of the bus Enhanced I2C (FAST mode). Extended addressing (new I2C standard). Q&A section.
Is there something like a Buffer  for I2C ?
What is the maximum distance of the bus ?
Can i isolate an I2C bus ?
Is there something like an I2C controller ?
How to generate a repeated start condition ?
Is it okay to abort an on-going transmission any time ?
Do i need to give the ack in read mode on the last byte ?
Why does the clock line  need to be bidirectional ?
Can i monitor an I2C bus in some way ?
Is there a way to test/debug I2C buses ?
I want to experiment with I2C .Are there demokits available.?
Are there plug in board available for IBM Pc to emulate I2C ?
I have problems with long buses. Can i make an active pull-up ?
An I2C driver in Pseudocode.
Driver Functions
Debugging Tools.
I2C trigger generator.
Checking who is controlling the bus.
I2C interface system for IBM-PC
Hardware
Software
Quickbasic / PDs / PowerBasic Driver for I2C Legal notes and Copyrights ACCESS Bus I2C on your MotherBoard SOURCES OF INFORMATION ON I2C
FTP sites
Web pages about i2
I2C PRODUCTS
Free development tools
Commercially available products
I2C Documentation
Periodicals that have articles covering I2C
Books
Troubleshooting Last Words ...

Preface


Hi and welcome to the latest edition of the I2C FAQ. Over the years I have been supporting people in their attempt to master this bus. I have collected a total of over 500 e-mails with questions ranging from beginner level to things that even I could not solve in 1-2-3. I Will try to summarize the knowledge I obtained in this revision of the FAQ.

I Would like to thank all the people who have bombarded me with interesting stuff and questions about I2C. I am also happy that my little knowledge could help.

Vincent September 1st 2000.
Back to Main Index

About this FAQ

Who put this FAQ together?
I put this FAQ together in response to my own frustration in searching for information about I2C. I have been playing with the bus for some time and, although I am not an expert on this matter, i think my, and other people's, experiences with the I2C BUS can solve common problems.
Back to Main Index


How can I contribute to this FAQ?
If you have any suggestions or additions please inform me or the future maintainer of the FAQ.You can contact me by e-mail : [email protected] ( valid until 1 Jan 2001 ) after that E-mail will most likely no longer be possible.

I hope that those of you who know of interesting items for this FAQ will share with everyone. A good amount of stuff is turning up thanks to everyone's help. If you have a website you can put the FAQ or a link to the FAQ online there.
Back to Main Index


What newsgroups will it be posted in?
This FAQ has been posted a last time to the following newsgroup: sci.electronics.design
Back to Main Index


May I distribute this FAQ ?
I am putting no restrictions on the use of this FAQ except - It must be distributed in its entirety with the copyright notice, and no financial gain may be realized from it. After all, I have spent, and lot of time on this. The only thing that I intend to gain from it is more information on I2C. For this reason I have appended a copyright statement to the end of this FAQ. I feel pretty silly doing this, but I just want to protect myself.

The copyright does not limit the use of this FAQ for noncommercial purposes. I hereby give my permission to one and all to pass this FAQ around and post it wherever you want - as long as it is not for financial gain.

You are allowed to distribute portions of the FAQ as long as you incorporate the following note. 'Taken from The I2C FAQ' and provide a link to its storage on the internet.
Back to Main Index

ABOUT THE I2C Bus

Historical background.
The I2C bus was developed in the early 1980's by Philips semiconductors.Its purpose was to provide an easy way to connect a CPU to peripherial chips in consumer applications (radio's, TV-sets etc).

Normal Computer systems use ByteWide buses to accomplish this task. This results in lots of copper tracks on PCB's to route the Address and datalines. Not to mention a bunch of address decoders and glue logic to connect everything.

In mass production items such as TV-sets, VCR's and audio equipment this is not acceptable. Complex circuits often need multilayer boards, and these are simply too expensive for household goods. Furthermore lots of control lines implies that the systems is more susceptible to disturbances by EMC and ESD.The research done by Philips Labs in Eindhoven (The Netherlands) resulted in a 2 wire communication bus called the I2C bus.

I2C is an acronym for Inter-IC bus. Its name literally explains its purpose: to provide a communication link between Integrated Circuits.

Nowadays the extent of the bus goes much further than Audio and Video equipment.The bus is generally accepted in industry. Offsprings like D2B and ACCESS have made an attempt to find their ways into computer peripherals like keyboards, mice, printers, monitors, etc... . However they have been successed by the USB bus. Amazingly the USB bus steals some technology frmo I2C. The basic communication idea and adressing scheme is based on I2C.

The I2C BUS has been adopted by several leading chip manufacturers like Xicor, SGS-Thomson, Siemens, Intel, TI, Maxim, Atmel, Analog Devices.
Back to Main Index


I2C Bus protocol
The BUS physically consists of 2 active wires and a ground connection. The active wires, SDA en SCL, are both bidirectional. Where SDA is the Serial DAta line and SCL is the Serial CLock line.

Every component hooked up to the bus has its own unique address whether it is a CPU, LCD driver, memory, or complex function chip.Each of these  chips can act as a receiver and / or transmitter depending on its functionality. Obviously an LCD driver is only a receiver ,while a  memory or I/O chip can both be transmitter and receiver.  Furthermore there may be one or more BUS MASTER's.

The BUS MASTER is the chip issuing the commands on the BUS.  In the I2C protocol specification it is stated that the IC that  initiates a data transfer on the bus is considered the BUS MASTER.  At that time all the others are regarded to as the BUS slaves.

As mentioned before, the IC bus is a Multi-MASTER BUS. This means  that more than one IC capable of initiating data transfer can be  connected to it. As MASTERs are generally microcomputers let's take a  look at a general 'inter-IC chat' on the bus.

Lets consider the following setup :

Case :  The CPU wants to talk to one of the attached components.

The CPU will issue a START condition  (see further on for description of all these conditions).  This acts as an 'ATTENTION' signal to all of the connected  ic's. ALL IC's on the bus will listen to the bus for incoming data.

Then the CPU sends the address of the device he wants to address.This takes 8 clock pulses. At this moment in time all  IC's will compare this address with their own.If it doesn't  match they simply do nothing and wait until the bus is released  by the STOP condition.If the address matches however the chip will produce a responce on the ACKNOWLEDGE signal of the CPU.

The ACKNOWLEDGE signal is issued by the CPU.When the chip whose  address matches sees the ACKNOWLEDGE on the bus it Pulls the  data line LOW. This is an indication to the CPU that there is  a chip with the wanted address on the bus.

Now the CPU can start transmitting or receiving data  In our case the CPU will transmit data.When all is done the  CPU will issue a STOP condition. This is a signal that the bus  has been released and that the IC's may expect another  transmission to start any moment.

We have had several states on the BUS right now :  START, address ,ACKNOWLEDGE ,DATA ,STOP. These are all unique conditions on the BUS. Before we take a closer look into these I will talk about the hardware of the BUS. This is necessary to understand what is physically going on.
Back to Main Index


Hardware layout of the I2C bus.
As stated before the BUS consists of 2 active signal lines and a ground  potential. Internally in the chip the bus looks like this :

The bus interface is built around an input buffer and an open drain or open collector  transistor. When nothing happens the bus lines are in the logic HIGH  state. Note here that an  external PULL-UP resistor is neccessary. This is an error that most beginners make. To put something on the BUS the chip drives  its output transistor, thus pulling the BUS to a LOW level. When the bus is IDLE ( nothing going on ) both lines are HIGH. The HIGH state is defined as NOT LOW (obvious isn't it).

What i mean here is that you cannot set a voltage on the HIGH Level. It depends on the supply voltage of the connected IC's.However as this is mostly 5 Volts you can say that HIGH is 5 volts and LOW 0 volt. Nowadays the 3.3 volt ic's are emerging rapidly. It's clear that in this case the high level will be 3.3 volts. The latest revision of I2C provides a means of interfacing mixed voltage circuits.

The nice thing about this concept is that it has a 'built-in' bus mastering technique. If the bus is 'occupied' by a chip that is sending a 0 then all other chips loose their comm's capability. More will be explained about this further on in the Faq.

However the open collector technique has a drawback too. If you have a long bus this will have a serious effect on the speed you can obtain .  The higher this RC constant the slower you can go. This is due to the effect that it influences the 'sharpness' of the edges on the I2C bus . At a certain point the chip will not be able to distinguisch clearly between a logic 1 and 0.

Long lines present a capacitive load onto the output .Since the pull-up is passive you are facing an RC constant which will reflect onto the shapes of the signals.

What's more is that you can get reflections at high speed .This can be so bad that 'ghost signals' disturb your transmission and corrupt the data you transmit. And then even the Schmitt trigger at the input of the chip will not keep you out of trouble. The following image shows you exactly what can happen.

Therefore some strict electrical specs have been set forth. These are explained further on.

To overcome this problem , Philips has developed an Active I2C terminator. This consists of twin charge pumps. You can look at this device as a dynamic resistor. The moment the state changes it provides a large current (low dynamic resistance) to the bus. Doing this it can charge the parasitic capacitor very quickly. Once the voltage has risen above a certain level the high current mode cuts out and the output current drops sharply.

Back to Main Index

BUS Events


I Have already mentioned some things like START, STOP, ACKNOWLEDGE,  SLAVE, MASTER and so on. In this section these things get explained.  When reading this you must keep the following 2 things in mind.

A MASTER is the device that initiates a message. Thus he controls the SCK line. The MASTER always generates the Clock pulses.
A SLAVE listens to the master and will send data only when asked.
The SDA and SCL lines can only be PULLED low. They cannot be DRIVEN  high. To make them high the device just releases the line.  The external pull-up resistor does the rest of the work.

Back to Main Index


Start And Stop condition.
A START condition looks like this:

The bus is in idle mode when both Data and Clock line are high. The chip issuing the Start condition ( the bus MASTER ) first pulls the SDA (data) line low and then pulls the SCL (clock) line low.

A STOP condition is just the mirror of the above.

The Bus MASTER first releases the SCL and then the SDA line.

The start condition acts as a signal to all connected IC's that something is about to be transmitted on the BUS. All the devices on the bus will go to listen mode and check the incoming data for a match against their address on the bus. The Stop condition  tells the connected chips that the message has been completed and that the bus is free to use.
Back to Main Index


Putting something on the BUS
Putting a bit of any kind on the bus looks like this :

First the MASTER sets the data line to the appropriate level by pulling or not pulling the SDA line low. Then it releases the SCL line for some time and pulls it low again. Now it can change the state of the SDA to the level required for the next bit and the process continues all over again.

The DATA must stay valid during the HIGH level of the CLOCK pulse. If the data chenges while the clock line is high this will bee seen as either a START or STOP condition occurring ! ( depending on the direction of change ).

Using the above information ,a transfer could look like this :

As you can see in the above it is not necessary to have a clock with a constant duty cycle.The BUS is very relaxed even in such a way that you can stop the clock in the middle of a transaction and then continue later on. This is very useful. Consider the following :

Your cpu is in the middle of a transaction and gets an interrupt. It can process the interrupt first and continue its message later on without any problem. (try doing that on RS232 !). Since there is no minimum clock speed set you can have the communication running at whatever speed you can handle.
Back to Main Index


Addressing a SLAVE.
EVERY byte put on the BUS MUST be 8 bits long. (8 clock pulses).

A byte is always sent with the MSB first. The number of bytes that can be transmitted in one data 'telegram' is unrestricted. ('Data telegram' is everything going on on the bus between a START and STOP condition). However it is allowed to end a transmission any time by sending a STOP condition. Even when you are only 4 bits far in your telegram. Actually what happens is that the STOP condition resets the bus control logic of all connected chips. They start looking for a START condition again.
Back to Main Index


Waiting for ACKNOWLEDGE.
When a chip is being addressed or has received data it will issue an ACKNOWLEDGE pulse. Therefore the MASTER must first (1) release the DATA line (set it to high level). The Slave performing an ACQ will pull the DATA line low (2) Shown as the fat line on the image below.

The MASTER will now send a clockpulse over the SCL line(3). When the clock pulse has been completed ( SCL goes low again ) the slave will release the DATA line(4). Now that the MASTER knows that the SLAVE is actually there it can continue. Generally the MASTERs (mainly CPU's running software) use a timeout value. When no chip is responding after some time they issue a STOP and then continue with their work. This prevents your software from locking up if for some reason the addressed chip is not replying.

Concerning the SLAVE pulling low the SDA line it is so that generally the addressed IC will already have pulled the SDA line low even before the MASTER has set the clock HIGH. It is the falling edge of the last clockpulse that triggers the slave.

In the real life it is good practice to actually look during the high level of the CLOCK if the SDA is being pulled LOW or is LOW. Some chips need some time to process the address before they can respond by pulling the SDA low. This can be the fact when the addressed SLAVE is another CPU or an EEprom. Suppose the following : You address a SLAVE CPU. But just before the SLAVE CPU can pull the SDA low it has to process some interrupt occuring.If the transfer issuing CPU would look to the SDA line immediately it would see a HIGH level. Thus it would look like the SLAVE is not responding. The Same goes for EEproms. Since storing data to EEprom cells takes some time the ACKNOWLEDGE is used to indicate that the programming has been completed. So after the last bit has been transferred the EEprom starts writing the received data into its array. It leaves the SDA line in the LOW state until this action has been completed. this means that after the ACQ clockpulse the slave keeps the SDA line LOW !. It is the task of the masdter to wait now until SDA becomes high before continuing. this process might seem to violate the I2C bus spec but actually it doesn't. This process is called synchronisation. ( see the topic explaining this process ).

I have once spend a whole day figuering this one out !.The system once in a while did not work like it should have because the addressed device was not capable of generating an ACKNOWLEDGE in time.

The best way to do an ACKNOWLEDGE , in my humble opinion,is like this: Put the SCL high, wait some time (your TIMEOUT value), then check if SDA is LOW. If it is LOW - > The chip is there. If it is HIGH -> The chip isn't there. When removing the ACQ clockpulse check if the SDA line effectively goes high. If not : the chip is in process of writing internally.

Back to Main Index


What happens next ?
Now that the SLAVE has been addressed and responded to the ACKNOWLEDGE the rest of the telegram (until we issue a STOP) depends solely on the addressed chip. You can just send one or more bytes to the chip or receive one or more bytes from the chip. It can even be that you first write something and then read something from the chip.
Back to Main Index


Writing One or More Byte's to a Slave.
After the Device has responded with an ACKNOWLEDGE (see above) you just send another 8 bits on the bus. Now you have to wait again for the SLAVE to ACKNOWLEDGE. If you are through you issue a STOP command and then the bus is released again. If you need to send more then you just send another 8 bits and wait for an ACKNOWLEDGE. And so on and on and on.

I figuered out in real life that on the last transmitted byte you do not have to wait for the ACKNOWLEDGE. You can directly issue a STOP command. Apparently there are some chips that do not generate an ACKNOWLEDGE here !. Theoretically they should generate an ACKNOWLEDGE but for some reason they don't. The best way is as follows : after you have transferred your last byte just to set the SCL high , wait some time , take it low and then issue a STOP command. There is an exception though.

Devices like serial EEproms use the ACKNOWLEDGE for storing the information in the Memory array.They do not pull the SDA line low until the programming has been completed.In that way the MASTER has a way to know if the data has been written succesfully.Storing data in EEprom memory is rather slow.So by monitoring the SDA line the CPU knows when the chip has completed the WRITE to its memory array.
A byte write could look like this :
------------------------------
|S|SLAVE address|WA|DATA|WA|P|
------------------------------
A multi byte write looks like this:
-----------------------------
|S|SLAVE addr.|WA|DATA|WA|...
-----------------------------
----------------------
...|DATA|WA|DATA|WA|P|
----------------------
Note :

S  = START
WA = WAIT FOR ACKNOWLEDGE
P  = STOP

Back to Main Index

Reading one or more bytes from a slave.
Looks kind of the same as a byte write. The difference is the handling of the SDA line and the ACKNOWLEDGE.
The MASTER generates a START , transmits the device address and waits for an ACKNOWLEDGE. So far so good. Now the MASTER has to RELEASE the SDA (data) line. The SLAVE will pull it low when needed. On every clock pulse , that the MASTER generates ,the SDA line will be in the state set by the SLAVE.

When all 8 bits have been read the MASTER must GIVE the ACKNOWLEDGE or to the SLAVE  or stop the transmission.

To give an acknowledge to a slave the master holds the SDA line low and gives a clockpulse on SCL. To stop stransmission you simply issue a stop condition on the bus : Keep SCL and SDA low. Now make SCL high , and then make SDA high.

If you give an ACQ pulse to the slave you have to read another byte. Immediately after the ACQ the slave will take hold of the SDA line and you might no longer be able to give a stop before clocking out the next 8 bits.

Note: Here the FAQ has been greatly modified. In the previous FAQ the text caused a lot of confusion.

Back to Main Index


Determining the SLAVE Access mode
Now there is one thing i haven't told you yet. How does your SLAVE  know whether you want to read from or write to it ?

Thats an easy one. This is beeing determined by the SLAVE address.  Each byte consists of 8 bits. The 8th bit in the SLAVE address has a  special meaning. When it is set to 0 it means you want to write to  your SLAVE. When it is set to 1 it means that you you want to READ.  You could see this as follow. The Even addresses are WRITE addresses, the ODD addresses are READ addresses. Each device has a consecutive WRITE and READ address.

Example :  a PCF8574  General purpose 8 BIT I/O port.

SLAVE address to WRITE is (01000000)b  = 64d
SLAVE address to READ  is (01000001)b  = 65d

So you can have a theoretical maximum of 128 device on you BUS. Practically this is not the case. There have been set up a couple of addresses which you are not allowed to use.(more about this later on).  Now there is one more type of DATA telegram.
Back to Main Index


The Combined data format.
This is a format generally used by memory devices. Suppose you have an 128 byte deep memory on the bus and you want to read the 84th byte. Normally you would have to read the first 83 bytes before getting what you want. This takes too much time and occupies the  bus. In this case there are two possibilities. You first write to the SLAVE address a byte which tells it on which location you want to read. Then you start a read operation. That is one way of doing it. A more elegant way to do this is using a combined mode telegram.
---------------------------
|S|AS WRITE|WA|SEND BYTE|..
---------------------------
-------------------------
..WA|S|AS READ|WA|READ|P|
-------------------------
To start this sequence you access the chip in write mode. AS WRITE = Address Slave in WRITE mode (even address). Wait for ACKNOWLEDGE and WRITE a byte. This byte is beeing treated by the memory as the location pointer. (that is how i2C memories work). Then you wait for an ACKNOWLEDGE by the SLAVE and you generate another START condition. Now you send the SLAVEs READ address ( ODD address ) Wait for ACKNOWLEDGE and you receive the data byte. From now on  you are in standard READ mode. So you can now either send a STOP or continue reading from your SLAVE by giving an ACQ to the slave and clocking out the next byte. All memory devices auto-increment their location pointer.

Now you can even go one step further and generate another START and then address the SLAVE as write. Send a new Data byte (which acts on  the location pointer), send another start, enter read mode etc ......  This combined mode is really a very flexible means of addressing complex components. This may look very messy. But it has its pro's and con's:

PRO: If you have 2 CPU's on your bus which could want to take the bus this will assure you that you will be able to continue your  actions on the bus without interference from the other CPU. Remember that when you have generated a START and have sent the SLAVE address the other CPU too will be waiting until a STOP appears on the bus. So he will not try to put something on the  bus.There could be a risk involved using normal READ and WRITE operations

Picture this situation : CPU 1 accesses the MEMORY and sets the location pointer to 84 and issues a STOP condition. Now the BUS is FREE. CPU 2 sees this and thinks : okay my turn. He sets the location pointer to 92 because he wants to do something at that location. Now the bus is free again. CPU 1 says : aha ! the bus is free. Time to write for me. Now the data will land on location 92 and not on location 84 as it should have been. So : If you are dealing with memories on a Multimaster bus always use this last method.  It keeps you out of trouble.

CON:  If you have lots of operations to do you can create a bottleneck situation. The other CPU could be waiting and waiting for a  chance to have his turn on the bus.

But is you don't have a MultiMaster environment this all is not necessary.

Congratulations you have reached the EXPERT grade.  :-)
Back to Main Index

MULTIMASTER communication

As stated above you can have more than one CPU on the BUS. When you have only one CPU there are no risks of having collisions on the bus. That situation changes with 2 CPU's.

When CPU 1 issues a START and sends an address the other one will back  off. Because of the fact that if the address does not match his own  address he has to wait until the bus is free. (STOP condition). So far  no problem. But as Murphy is, as usual ,always around. It's when you least expect it that it goes wrong.Fortunately the BUS setup helps us out here.

When you (as a MASTER ) change the state of a line to HIGH , you MUST always check that it has gone to the HIGH level. If it hasn't : BACKOFF ! it's occupied !. Wait for a STOP to occurr and then retry.

What could happen is that the TWO CPU's start communication on the  same moment in time.Since it is an open collector/drain bus they can  only PULL the line low. They cannot force it HIGH. (they can only  leave it HIGH by not turning on their output transistor).

So they start transmitting. And all goes well as long as they both are  asserting the same levels. (during START it's okay.They are doing the  same) Then they start transmitting data. for the first couple of bits all goes well until suddenly diaster strikes. Bit 3 is different !. CPU1 wants to send a 0 while CPU2 wants to send a 1.

Now CPU 1 has pulled SDA LOW. CPU 2 leaves SDA open. Remeber that you cannot force the Line HIGH It is the job of the pull-up resistor to do that.  Since they are both running clean and good written code they are  testing what they have put on the BUS. CPU 1 sees that he has written a 0 and says 'okay for me'.. CPU 2 on the other hand sees that the line is LOW  while he has left it HIGH ! so he knows that by now someone else has taken control. Time to  BACK OFF !.

Now in an ideal world CPU2 would do even more !. When he knows for sure that this is the first byte after the START generation he will switch from tranmist to receive mode !. Why ? Well simple: CPU1 might be trying to talk to CPU2 !
If this is the first byte after a START condition this means that it is effectively a slave address beeing transmitted. CPU2 has to check that this slave address beeing put on the bus is not his own. If it is not his address he has to wait for the STOP command to appear on the bus before attempting to take control again. On the other hand. If the address is his own address he must respond. In the  latter case CPU2 becomes the slave device on the bus. This way all ends up well.

So from the above story we can conclude that is the one that has its  line LOW that always wins. The One wich wanted the line to be HIGH when  it is beeing pulled low by the other looses the BUS.We call this a 'loss of arbitration' or BACK-OFF. When a BACKOFF situation is generated it is good practice to have the cpu, that has to BACKOFF, wait for a STOP condition to appear on the bus.The other one is still busy transmitting.

The above example showed a situation where the two CPU's were in perfect sync with each other. In most situations this will not be the case. But even then the arbitration will still work. Suppose one of the CPU's missed the START condition and still thinks nothing is going on ... , or it came just out of reset and wants to start talking on the bus. These are real-life cases that WILL happen in a mulitmaster environment. ( remember Murphy's Law !) . Consider a multimaster system that has just been powered up. You will not know which cpu will come out of  reset first.

So actually this mechanism does not only do arbitration , it is also very effective at ensuring that the information beeing sent is not lost or corrupted !. The message from the winning CPU is not distorted in any way.

If you struggled trough all of this , and the previous chapters then you are ready to face the world of MultiMaster I2C
Back to Main Index


Bus synchronisation
The i2c protocol also includes a synchronisation mechanism. This can be used between masters. However to my knowledge there are no chips that use this mechanism. This must be implemented in software.

When a slower slave is attached to the bus then problems may rise. Suppose the following : The master reads a byte from a slave. Lets say an A/D convertor. The slave needs some time to make a conversion. The master adresses the slave in read mode
--------------------...
|S|READ_ADRESS|WACK|...
--------------------...
In the Wait_for_ack module happens something worth looking at.

In a normal ACQ sequence the slave will pull the ACQ line low immediately after the 8th clock pulse and before the ACQ clockpulse. The master will send a clockpulse , and sample the SDA line during this pulse. If SDA is low it means that the slave aknowledges the information sent. When the ACQ clockpulse is removed the slave releases the SDA line.

Now lets suppose that the slave has detected his home adress. It starts a conversion and waits until this conversion is done before giving acknowledge.That way the master can read the result immediately after the Acknowledge sequence. Of course the master would have timed out and considered the slave not to be present on the bus.

Now the synchronisation meachanism can come in handy. The Slave can pull the SCL low as long as needed. The master is then not able of giving the ACK clockpulse because it cannot  raise the SCL line.Of course the master software must check this state. This is the routine the master must execute for a synchronisation aware Wait_for_ack sequence

What happens is this : (in our theoretical model)

The master has sent the last bit of the slave adress on the bus. The slave recognises its adress and pulls the SDA line low.  ( it wants to acknowledge because it has detected its adress ).  At the same time it starts the A to D conversion and pulls the SCL line low.

The master now wants to start the Wait_for_ack sequence. So it makes SDA high.( Never minding the Slave holding it low )

Now the master releases the SCL line.When testing the level of the SCL line the master will see that it is still low.This is due to the fact that the slave is holding the SCL low.So the master enters a loop that runs until the SCL line effectively turns high. The moment the slave has completed the conversion it releases the SCL line.

The master detects that the SCL has become high and checks the SDa line. Since the slave turned it low long ago it sees a valid acknowledge. The master will now begin to read the result of the conversion.

This technique is used by the serial EEproms on I2C. There are a number of drawbacks involved when implementing this.  If the bus gets stuck due to an electrical failure of a circuit the master can go into deadlock.Of course this can be handled by timeout counters.

Another drawback is speed.The BUS is locked at that moment. If you have rather long delays (long conversion time in our example above) then this  penalizes the total bus speed a lot.

The existing A/D convertors do not use this synchronisation system. They use the following technique :

Adress chip. Slave will ack and starts new conversion.
The master reads a byte and sends stop.
This byte is the result of the previous conversion.

The next time the master reads the chip it will read the value cycle above.  Between the 2 accesses the bus is free for the master or another master  to access a different slave. When the A/D has not completed conversion it can also simply not ACK. The master Wait_for_ack will timeout and the master will continue. It is the masters task to attempt a retry.

The Synchronisation mechanism is nothing else than a sort of handshaking. In a multimaster environment there is the risk that , when the 2 masters are talking to each other,using this handshake routine, they go into deadlock.

Master 1 attemps to adress master 2. He succeeds.But during the ACK sequence master 2 has to service an interrupt therefore he keeps SCL low. Master 1 will now wait for the SCl line to come high. Master 1 times out (because for some reason master 2 is still busy).  Master 1 completes transaction and starts a retry. In the mean time master 2 came on line again and released the SCL line but is still pulling the SDa line low. Result Master 1 cannot start a  new transmission. Because it will get a backoff situation  ( bus is not free ).Master 1 will get stuck in an endless retry routine. While master 2 will be endlessly waiting for master 1 completing  the ACK. Result : System in complete deadlock.

When using the synchronisation mechanism you must take care to avoid all possible causes of a deadlock.This makes the interface driver very complex.
Back to Main Index

Special addresses and exceptions.

During the above i have mentioned that there are some exceptions about device addressing. Not all addresses can be used. There are some that have been reserved by PHILIPS for special purposes.

  address  R/W
  0000 000 0  : general call
                address
  0000 000 1  : start byte
  0000 001 x  : CBUS address
  0000 010 x  : address
                reserved for
                different bus
                format.
  0000 011 x  !
  0000 100 x  !
  0000 101 x  !} to be defined
  0000 110 x  !
  0000 111 x  !
 

This implements that all addresses below 16 are reserved for special  purposes. The reason behind this is that there are other buses around. Using this scheme you can connect device that uses a different bus to the I2C bus !. It is possible to put SPI, I2C, uWIRE and CBUS devices on the same I/O pins of your CPU. Since all buses different to I2C use 3 lines you can
cut down on you CPU pin load.

How this exactly works would lead us too far. Maybe in the future someone will explain this. If somebody out there has experience with these other buses ? Could be interesting.

CBUS is the ancestor of I2C. It was also developed by Philips.
SPI is (c) Motorola
uWIRE is (c) National Semiconductor

Back to Main Index

Some general notes about these reserved addresses.
The general call address is received by all IC's on the bus.  If there is an IC out on the bus that can process this address it will  respond by generating an ACKNOWLEDGE. See Datasheets for info on which  IC use them and why. You could use this to invoke some special command in a MultiMASTER environment. (Like reboot all CPU's or whatever. Since all chips will
respond to it ,it can be used for this purpose. However take care not to mess up anything else.) There have been determined some actions on receipt of the General call address.

When the second Byte in a telegram containing a general call is :

00000110  :This is a RESET condition. All IC's capable of handling a general call message will reset and reload their SLAVE   address.There are I2C compatible IC that have part of  their address programmable.This allows you to have more  than one IC of a certain type on your BUS. Further about  this later on. They also set all their internal registers to the power-up state.
00000010  :The same as above except that you must provide the SLAVE address.This does not RESET the registers to Power-up state.
00000100  :Causes all IC's that define their address by hardware to reload this value.This does noet reset internal register.
00000000  : PROHIBITED.
xxxxxxx1  : This is a HARDWARE general call. You can look to this as a kind of INTERRUPT generated by an I2C IC.

This can be used in the following condition.: You have a keyboard controller. Each time a key is pressed  it transmits the following sequence :
-------------------------
|S|00000000|A|yyyyyyy1|..
-------------------------
----------------
.. A|Databyte|P|
----------------
Where yyyy yyy is its own address. What will happen is that the MASTER CPU will see the General call address and see that the device with address yyyy yyy has something to tell to the CPU. It will read the next byte. In our case the CPU will know that keyboard controller yyyyyyy has detected a key and that the scancode of this key is contained in the received databyte.

All other codes have not been assigned. All I2C ic's are designed  to ignore them. So you are free to use them for whatever. (I generally use them to debug MultiMASTER modes).

NO IC is allowed to generate an ACKNOWLEDGE of the START byte.
The start byte is used to syncronize Slow devices with fast devices.
The CBUS address is used in this way : After sending this address all IC's go into IDLE mode until they receive a STOP condition. In the mean time you can transfer data using a complete different protocol on your I2C bus.

Back to Main Index

Electrical spec's of the I2C Bus


As the chips designed for an I2C bus can function on different Supply voltages the following levels have been set.

LOW level input voltage : -0.5v to 1.5v
LOW level relative to VDD : -0.5v to  0.3*Vdd
HIGH level input voltage : 3.0v
HIGH level relative to VDD  0.7*Vdd to Vdd

For other electrical specs please refer to the component datasheets. The number of interfaces connected is limited to the number of available addresses and the load capacitance on the bus. This capacitance may not be bigger then 400pF. In the new standard this is preferred to be less than 200pF.
Back to Main Index

Enhanced I2C (FAST mode)

Since the first I2C spec release (which dates back from 1982) a  couple of improvements have been made.In 1993 the new I2C spec was  released.This new spec conatains some additional sections covering  FAST mode and 10 -Bit addressing.  In this section the Fast mode will be covered , while in the next  section information about 10 bit addressing is given.

In the FAST mode the physical bus parameters are not altered. The protocol,Bus levels,Capacitive load etc.. remain unchanged. However the datarate has been increased to 400 Kbit/s. To accomplisch this task a number of changes have been made to timing.

Since all CBUS activities have been canceled ,there is no compatibility anymore with CBUS timing.The development of IC with CBUS interface has been stopped. The existing CBUS ic's are being taken out of production.

The input of the FAST mode devices all include Schmitt triggers to suppress noise. The output buffers include slope control of the falling edges of the SDA and SCL signals.If the power supply of a FAST mode device is switched off the BUS pins must be floating so that they do not obstruct the bus.

The pullup resitor must be adapted. For loads up to 200 pf a resistor is sufficient.For loads between 200pf and 400pF a current source is preferred.

Back to Main Index

Extended addressing


Due to the increasing popularity of the I2C bus the address space is nearly exhausted.This starts posing problems for people currently in the phase of designing a new I2C compatible IC. Therefore the I2C standard has been adapted.

A chip that conforms to the new standard receives 2 address bytes. The first consists of 5 * a ONE ,the 2MSB's of the address and the Read/Write bit. The second byte contains the LSB's of the address.
-----------------------
|S|11111A9A8 R/W|WA|...
-----------------------
-----------------------
A7A6A5A4A3A2A1A0|WA|...
-----------------------
This scheme insures that the 0 bit addressing mode stays completely transparent for the other devices on the bus. Normally any new design should adept to this new addressing scheme.
Back to Main Index

Q&A section


What is the maximum distance of the bus ?

This depends on the load of the bus and the speed you run it at. In typical applications a few meters (3 to 4). Better: The maximum capacitive load has been specified (electrical Spec's in this FAQ).

If you run at a lower clock frequency then you could go further. If you are careful in routing your PCB's and cabling then you can take it further.I once had an application that had a total of about 100 meter cable in it. The entire system was clocked on something like 500 Hz. I used twisted pair cable and twisted SCL with GND and SDA with VCC. No problem.The systems is now up and running for over 5 years.

If you need to go far at high speed then you can use an active current source . Philips has a standalone product for this purpose. Or you could build one yourself. Another thing to be taken into account is the amount of noise picked up by long cabling. This
noise can disturb the signal transmitted over the bus so badly that it becomes unreadable.

A last thing to be taken care of is the bus termination. Long lines will cause refelections. These reflections can cause 'ghost signals' to appear.This kan be overcome by using a charge pump mechanism like the Philips device has. See also next topic.

I want to extend it ''by the book''. Is there something like a Buffer  for I2C ?

Yes indeed this exists. Philips manufactures a special chip to buffer the bidirectional lines of the I2C bus. Typically this is a current amplifier. What it does is force current into the wiring  (a couple of mA). That way you can overcome the capacitance of long  wiring. Philips P87B715

However You will need this component on oth sides of the line.The charge pump in this devices can deliver currents up to 30mA. And that is way too much for a normal I2C chip to handle.With these buffers you can handle loads up to 2nF. The charge amplifier 'transforms' down this load to a 200pF load which is still acceptable by I2C components. Another possibility is to make such a charge pump yourself. This is fairly easy and can be accomplished by 1 chip and a few resistors. See a bit further on for details.

Can i isolate an I2C bus ? (using optocoupler or whatever)

This is possible. The circuit is rather complex due to the bidirectional nature of the I2C BUS. Actually there are a number of solutions here. One has appeared in electronic design new , one is included in the elektor book on i2c and yet another one has been published in an issue of Elektor. See the end of this FAQ for information on these books.
However : Here it comes (for once channel).


Component Values

1: 270 Ohm
2: 3300 Ohm
3: 1800 Ohm
4: 1000 Ohm
5: PNP like 2n2219 or BC557
6: NPN like 2n2222 or BC 547
Optocouplers : 6n139 , 4n27 or Til 111

A couple of remarks. Since the speed of the I2C bus can be rather high it is reommended to use a fast optocoupler.However this circuit will not work on speeds higher then 10KHz.A 6N139 will do the job in all cases. The 2 PNP and 2 NPN transistors can be any standard type. Like 2N2219 and 2N2222 (USA) or BC547 and BC557 (EUROPE).

How does it work ?
The problem with bidirectional lines is that a buffer tends to get stuck on a certain level. In the above schematic this has been dealth with. In the following explanation we assume that the left side is transmitting and the right side is receiving.Since the circuit is symmetrical you could do it the other way around too. Suppose you send a logic 1 into the left side. The Led of the top optocoupler will stay dark. Since its transistor does not receive any light it is not turned on. The next transistor does not get driven and the line at the end is beeing pulled high via resistors 1' and 3' . The PNP transistor 5' will not get driven. So the Led connected to it will not light. So there is no feedback signal . So far so good.

Now lets look what will happen if we send a 0. The first transistor 5 will be turned on. Thus the led connected to it will start emitting light.This results in the fact that it's matching transistor will turn on . The transistor connected to the Emittor of will be turned on too. The output line is now beeing pulled low via resistor 3' . This low level would turn on the PNP transistor. This would result in The other optocoupler to light , it's transistor to turn on etc etc .. The circuit would go into a lock-up.
But since the NPN transistor is pulling the Anode of the led to ground this will not happen. In this way we have eliminated the deadlock.

What if i don't want to emulate the bus by software or if i don't have an I2C interface on my system ? Is there something like an I2C controller ?

Yes indeed. There is a special chip to do the I2C interfacing. The PCD8584 or PCF8584 incorporate a complete I2C interface. These chips are designed in such way that they can interface to almost any microcontroller or computer around.

I am puzzled on how to generate a repeated start condition.

I make the SCK high and my device pulls SDA low to acknowledge. So far no problem but how do i make a new start now ?. The device is pulling SDA low. !

First you have to complete you ACK cycle. To do this you must make SCL low again. The slave will release the dataline when it detects that SCL went  logic low.  Now you can issue a stop command. To do this you make the SCK  high again and then pull low the SDA line.  This is the confusing part of the procedure. Normally one would  suspect that by making the clock high again you will be clocking  in the first bit of a new byte. As a matter of fact that is the case.  But since the chip will detect a START condition this operation gets  cancelled.

Is it okay to abort an on-going transmission any time.

According to the specification this !should! work. It depends on the layout of the component. A real I2C compatible  ic will be able to handle this. You should test this before you  use it.
Normally when a START or STOP condition is detected the internal logic of the chip is forced into a certain state. Internally the part that detects START and STOP is differnet then the logic that does all other processing. The START together with the address register is to be considered as a functional unit inside the chip.

When a START is detected all internal operations are cancelled and the chip will compare the incoming data with its own address. When a STOP is detected ALL chip's on the bus will reset their  internal logic to IDLE mode. This is also used to cut power consumption. When a STOP is detected all logic is shut down except for the START detector. When a start is issued on the bus the START detector will 'wake-up' the rest of the internal logic.

Do i need to give the ack in read mode on the last byte.
 My chip starts sending data and occupies the bus ... .

This is a question that got me puzzled .Indeed this is a bit strange. Normally if you have read the last byte in a chip and generate an ACK  the chip should do nothing anymore. So the bus is clear for you to create a STOp condition. Apparently there are some chips that start transmitting data again.

Digging in to to spec showed an error in my FAQ. On the Last byte READ you must generate a NACK (NOT Acknowledge).  Check out the description of the READ mode

I read the SDA and SCL are bidirectional.Why does the clock line  need to be bidirectional ?

The clock line needs to be directional when using a MULTIMASTER protocol and when using synchronisation protocol. When you are using only one Master then this is not required since the clock will always be generated by the Master and you only  have one on the BUS. If you run Multimaster then this changes.The Master must be able to receive data from the other master. At that time it must be able to check the Clock line too. For more information about bus synchronisation check out the topic dedicated to it.

Can i monitor an I2C bus in some way ?

This is possible. There are a few commercial I2C monitor / debuggers around that can do this.Information on these cards can be found elsewhere in this Faq There is another possibility to do this. By using the PCF 8584 chip from philips. This is a universal CPU to I2C interface. This chip has a certain mode in which it takes not part in the real I2C action but unly records what is going on. It listens to all adresses but does not generate an acknowledge.Using some software routines and a small cpu you could make a universal I2C data logger.

Is there a way to test/debug I2C buses ?

There is no general way to Debug an I2C bus. However a few guidelines might help to get it running.
First thing is to check the levels on the bus. You should see a clear signal that has a low level that is lower then 0.8 volt and a high level which is at least 3.5 volts. ( assuming you are running in a 5 volt environment )

If the high level is not high enough or does not rise fast enough then you can try to lower the value of the pull up resistor. You must take care however not to surpass the maximum allowable current in the I2C driver stage . The minimum allowable resistor for a 5 volt drive I2C bus is 5volts / 3mA = 1600 Ohms. A typical value of 4700 ohm should do fine.

Make sure the bus is not 'stuck' . This could be the result of a bad power supply (chips go into latch up during power-on) or a bad chip .
also check the Troubleshooting section

I want to experiment with I2C .Are there demokits available.?

Philips has at least 1 board ( i know of two different boards) for these purposes. It features a bunch of different I2C devices such as EEprom ,digital I/O ,A/D D/A , controllable switch , Real time clock , Ram , Display driver (led and LCD with even an alphanumeric LCD) and also can host a number of their 8051 compatible CPU's.

For people wanting to control I2C from their pc they can either buy a card or build one themselfves. A number of Programs is available to control I2C devices from this interfaces. You can use the Philips / signetics software or use the driver i wrote to control the I2C bus from within your programs.

Are there plug in board available for IBM Pc to emulate I2C ?

There are a number of debugging tools out there which can monitor an I2C bus .
Philips has one of these tools available. Contact you Philips/Signetics representative for more information.
I2C Bus monitor MIIC-101

Micro Computer Control Corporation
PO Box 275
17 Model Ave
Hopewell New Jersey 08525
USA

Calibre ICA-90 I2C Adapter as IBM PC Plug-in Board
Calibre electronics Ltd
Broomfield House
Bolling Road
Bradford BD4 7BG
England
Also available from Farnell Components  Part no : 256-109 cost : approx 350 Us $

In USA you can also contact

Saelig Co.
1193 Moseley Rd
Victor New York 14564

I have problems with long buses. Can i make an active pull-up ?

Absolutely. If you need to go off board however then you should use the P87B715 device from philips.
for on board you can use following solution. Here comes the Schematic:

Now how does it work ?

First of all Rs. This is a series resistor used to minimize cross talk and undershoot .It also protects the I/O drivers of the I2C devices against overvoltages and overcurrent injection. These resistors are advised if you run a long bus on high speed ( such as in enhanced I2C mode). When the bus becomes free all output stages on the bus are turned off and SCL (or SDa for that matter) become high. This will not happen immediately , but the voltage will rise during a certain time. Now Suppose the switch is not there. The charge time of the bus capacitor is determined by the value of R1 only . The higher one of them is the longer it will take for the bus to reach a sufficient stable High level. We can't make the Series resistor too small because then we will go out of spec on the maximum allowable current into one I2C device when it turn's it's output driver on.

When we calculate for a current of 3ma we end up at approx 1800 ohms for the series resistance. 5volts / 3ma = 1666 Ohms .
To stay somewhere below this 3mA rating we take 1800 Ohms.The charge time for a bus capacitance of about 200pf would be around 360 nS. That is out of spec.The Spec for rise or fall time in Fast I2C is set to approx 300nS.
But we can't drop the value of our resistor without breaking the other spec of 3ma Max current.
Now if we had a means to change the value of the resistor temporarily.... And that's exactly what is done with the Analog Switch. If the voltage level sensed by the switch is in the range 0.8 to 2 volts then it will turn on. Meaning that the moment the voltage on the SDa line starts rising , this resistor will kick in and increase charge current to a value of 5volts/(1K8//1K2) =
720 Ohms. the charge current will then rise to 5 volts / 720 Ohms = 7 mA. This is allowable for a brief period of time. Of course all of this is a dynamic process. The actual charge current will change due to the fact that the bus voltage will rise.
A small graphical representation will explain more:


Wave 1 represents the turn off of the I2C device.So the bus must go to a logic 1
Wave 2 is the what you get if you only use a resistor. The bus 'slowly comes up to 5 volts due to the RC constant of Rpull-up and Cparasitic
Wave 3 shows the kicking in of the Analog switch. If the bus gets at approx 0.7 volts it kicks in and kicks out when the bus reaches approx 3 volts
Wave 4 is how the voltage on the bus changes. You can clearly see that it rises much faster when the switch is turned on.
And finally wave 5 show the current flowing into the I2C device. It starts at approx 3mA.

When the output stage is turned off this current slightly drops due to the fact that the voltage on the bus is rising. The moment our switch kick's in you see the current double. The same effect is then present as before the switch closed: the current drops as the bus voltage rises.When the switch opens again the current drops a little to charge the capacitor up to 5 volts. But at that time all chips already detect a logic one and are well withing the 300nS. Rise time.

Back to Main Index

An I2C driver in PseudoCode

This section covers a sample I2C driver. Currently Version 1.1

It is written in PseudoCode which is an imaginary programming language that any programmer should be capable of porting to his/her favorite language.

First we will define a set of basic interface routines. All text between / / is considered as remark. Following variables are used :

n,x = a general purpose BYTE
SIZE =  a byte holding the maximum number of transferred data at a time
DATA(SIZE) =  an array holding up to SIZE number of bytes. This will contain the data we want to transmit and will store the received data.
BUFFER =  a byte value holding immediate received or transmit data.


Driver functions

Basic functions
I2C_init : initializes I2C bus
Start : Sends a Start condition
Stop : Sends a stop condition
PutByte : Sends a Byte
GetByte : reads a Byte
GiveAck : Gives ACK to slave
GetAck : Gets ACK from slave
HighLevel functions
Read : Reads a byte from an address
Write : Writes a byte to an address
Randomread : Reads a block of data
RandomWrite : Writes a block of data


/$$$$$$$$$$$$$$$$$$$$$$$$$$$/
/****  I2C Driver V1.1  ****/
/    Written by V.Himpe.    /
/ Released as Public Domain /
/$$$$$$$$$$$$$$$$$$$$$$$$$$$/

DECLARE N,SIZE,BUFFER,X Byte
DECLARE DATA(size) Array

SUBroutine I2C_INIT
  SDA=1
  SCK=0
  FOR n = 0 to 3
      CALL STOP
  NEXT n
ENDsub
Back to Driver
SUBroutine START
  SCK=1
  SDA=1
  SDA=0
  SCK=0
  SDA=1
ENDsub
Back to Driver
SUBroutine STOP
  SDA=0
  SCK=1
  SDA=1
ENDsub
Back to Driver
SUBroutine PUTBYTE(BUFFER)
  FOR n = 7 TO 0
    SDA= BIT(n) of BUFFER
    SCK=1
    SCK=0
  NEXT n
  SDA=1
ENDsub
Back to Driver
SUBroutine GETBYTE
  FOR n = 7 to 0
    SCK=1
    BIT(n) OF BUFFER = SDA
    SCK=0
  NEXT n
  SDA=1
ENDsub
Back to Driver
SUBroutine GIVEACK
  SDA=0
  SCK=1
  SCK=0
  SDA=1
ENDsub
Back to Driver
SUBroutine GETACK
  SDA=1
  SCK=1
  WAITFOR SDA=0
  SCK=0
ENDSUB
Back to Driver
/ this concludes the lowlevel/
/ set of instructions for the/
/ I2C driver. The next       /
/ functions will handle the  /
/ telegram formatting on a   /
/ higher level               /

SUBroutine READ
 (Device_addr,Number_of_bytes)

  Device_addr=
  Device_addr OR (0000.0001)
   / This sets the READ FLAG /

  CALL START
  CALL PUTBYTE(Device_adress)
  CALL GETACK
  FOR x= 0 to Number_of_bytes)
    CALL GETBYTE
    DATA(x)=BUFFER
    IF X< Number_of_bytes THEN
       CALL GIVEACK
    END IF
  NEXT x
  CALL STOP
ENDsub
Back to Driver
SUBroutine WRITE
 (Device_addr,Number_of_bytes)
 Device_addr=
 Device_addr AND (1111.1110)
  / This clears READ flag /
 CALL START
 CALL PUTBYTE(Device_addr)
 CALL GETACK
 FOR x= 0 to Number_of_bytes
   CALL PUTBYTE (DATA(x))
   CALL GETACK
 NEXT x
 CALL STOP
ENDsub
Back to Driver
SUBroutine RANDOMREAD
  (Device_addr,
   Start_addr,
   Number_of_bytes)

  Device_addr=
  Device_addr AND (1111.1110)
  / This clears READ flag /

  CALL START
  CALL PUTBYTE(Device_addr)
  CALL GETACK
  CALL PUTBYTE(Start_addr)
  CALL GETACK
  CALL START

  Device_addr=
  Device_addr OR (0000.0001)
  / This sets the READ FLAG /

  CALL PUTBYTE(Device_addr)
  CALL GETACK
  FOR x= 0 to Number_of_bytes
    CALL GETBYTE
    DATA(x)=BUFFER
    CALL GIVEACK
  NEXT x
  CALL STOP
ENDsub
Back to Driver
SUBroutine RANDOMWRITE
  (Device_addr,
   Start_addr,
   Number_of_bytes)

  Device_addr=
  Device_addr AND (1111.1110)
  / This clears READ flag /

  CALL START
  CALL PUTBYTE(Device_addr)
  CALL GETACK
  CALL PUTBYTE(Start_addr)
  CALL GETACK
  FOR x= 0 to Number_of_bytes
     CALL PUTBYTE (DATA(x))
     CALL GETACK
  NEXT x
  CALL STOP
ENDsub
Back to Driver
/ $$$$$$$$$$$$$$$$$$$$$$$$ /
/  End of the I2C Driver . /
/ $$$$$$$$$$$$$$$$$$$$$$$$ /

Some notes about the high level routines. The READ and WRITE routine read/write one or more byte(s) from/to a slave device. Generally this will be used only with Number_of_bytes set to 1. An example :

PCD8574=(0100.0000)b
CALL READ(PCD8574,1)
result = DATA(0)

will read the status of the 8 bit input port of a PCD8574.

DATA(0)=(0110.01010)b
CALL WRITE(PCD8574,1)

will write 0110.0101 to the 8 bit port of the PCD8574

When do you need a multiread ? Consider a PCF8582 EEPROM. You want to read its contents in one time.

PCF8582=(1010.0000)b
CALL READ(PCF8582,255)

You can do the same with WRITE for the EEprom with the restriction that Number_of_bytes is not larger than 4. You will have to check the components datasheets.

The most useful instructions are RANDOMREAD and RANDOMWRITE.
Write 4 bytes of data to location 20h of the EEPROM

DATA(0)=(1010.0011)b
DATA(1)=(1110.0000)b
DATA(2)=(0000.1100)b
DATA(3)=(1111.0000)b
CALL RANDOMWRITE (PCF8582,(20)h,3)

The same goes for reading 16 bytes from the eeprom starting at adress 42h

CALL RANDOMREAD(PCF8582,(42)h,15)

The results are stored in DATA. All you have to do is read them out of  the array to process.  When you give the devices adress to these routines you don't have to care about the R/W flag. It will be automatically set to the right state inside the routines.
Back to Main Index

Debugging tools.


So you have an I2C bus and you want to monitor activity. Using a regular scope this is rather tough. When you are in control then you can easily generate a trigger for the scope. If you are not in control ( in a TV set or other equipment ) then things
get more complicated. The tools described in this section should provide some easy means to solve these problems.

I2C trigger generator.
This simple circuit allows any scope to trigger on an I2C transmission. Each time a start condition is detected the output of the flipflop will generate a pulse that can be used to trigger a scope..

The SCL and SDA are not connected wrong in the above schematic. You have to cross them in order for the circuit to detec the Start. Remember that Start means : a falling edge on SDA when SCL is high. And that is exactly what this circuit detects.
Checking who is controlling the bus.
To see who is actively pulling the bus low can be done using a simple resistor.


The low level generated by a slave will be lower then the low level generated by the master. this is easily recognizable on an oscilloscope. That way you can examine whis actually driving the bus. you could do the same for the clock line. then you can even look into multimaster environments.
Back to Main Index

I2C interfacing system for IBM-PC.


This section covers a complete I2C experimenting system for the IBM PC. In this section i will set up an environment to experiment with I2C.


Hardware section.

The schematic is almost the same as the Schematic provided by Philips. As a matter of fact it is the same.A little addition has been made. However it is 100% compatible with the philips driver schematic. This was done so you can use it both with tools like TV400 from Philips and with my driver.

SCL and SDA speak pretty much for themselves. The trig Output is an addition  i made to the original schematic. When used with the driver described below  it is able to trigger an oscilloscope. Each time a Start condition occurs the trig output generates a pulse.This will make it easier to monitor bus activity when experimenting wth the system. You can write a loop that keeps doing the same over and over again. When you connect SCL and SDa to channels X1 and X2 of the scope and the TRIG
 to the Trigger input. You can see the transfer on the bus.
Back to Main Index


Software

This module can be used with the programs developed by philips and available from their FTP site or from the internet.

Programs are TV400.ZIP and RAD216.ZIP. These contain a complete bus control terminal. You can monitor bus activity
 and also actively control lots of standard chips.It comes with libraries for nearly all Philips IC's available. You can also control Non-Philips  ic by using the universal bus interface.
Back to Main Index

Quickbasic / PDS / POWERBasic Driver

This describes a set a routines written Basic that allow you to run an I2C bus over a standard printerport. The program is written in such a way that it can be run on different platforms without ( or with minor ) modifications.

' ****************************
' * I2CDRIVE  I2C Bus Driver
' * (c)1995-2000 Vincent Himpe
' * Features  ICee Debugger
' * Released as PUBLIC DOMAIN.
' * Use as you please
' * This driver can be used
' * in Quickbasic ,PDS and
' * PowerBasic
' * PowerBasic users must kill
' * the 'Sub DELAY' since
' * powerbasic has this
' * feature.
' ****************************
' * ICee Debugger.
' * If during run of the
' * program the computer beeps
' * this means that an adressed
' * chip is not responding.
' * Turn on the debugger by
' * issuing the I2CDebugOn
' * command immediately after
' * opening the bus and rerun
' * the program. You will get
' * detailed error information
' ****************************

DIM ICdta(10)
COMMON SHARED I2CLoPort,
              I2Cmidport,
              I2CHiPort,
              I2Csavedstatus,
              SCL, SDA
COMMON SHARED I2Cdebug,
              I2Ctimeout,
              I2Cdevadr%,
              I2Cresult%,
              ICdta(), hold

' powerbasic users must replace
' COMMON SHARED by PUBLIC

hold = .001
' do not adapt this value.
' Adapt the value in DELAY

' $$$$$$$$$$$$$$$$
' $ Sample program
' $$$$$$$$$$$$$$$$

I2Copen 0, 1
' open port &h378 (LPT1)
' with ICee enabled

I2Cinit 10
' set a timeoutvalue

CLS

I2Cwrite 192, 12
' write '12' to device
' with adress 192

a = I2Cread(193)
' read a byte from
' the same device

I2Cwwsend 200, 1, 7
' write '7' to register
' '1' of device at adress
' 200

a = I2Cwwread(201, 1)
' read register 2 of
' device at 200

I2Cmultiread 200, 3
' read first 4 registers
' (0..3) of the slave at
' address 200

FOR a = 0 TO 3
    PRINT ICdta(a)
NEXT a
END
' ----------------------------
SUB delay (count)
  ' Notice about this routine.
  ' When using powerbasic you
  ' must delete this routine
  ' in its entirity. It is
  ' needed for Qbasic only.

  FOR a = 0 TO (count * 1000)
  ' adapt this value according
  ' to the CPU speed
  NEXT a
END SUB
' ----------------------------
SUB holdsystem
  ' Freezes the system so you
  ' can read ICee debugger
  ' messages
  CALL messg(" Press key ")
  DO
     a$ = INKEY$
  LOOP UNTIL a$ <> ""
END SUB
' ----------------------------
SUB I2Cclose
  ' Closes the I2C driver.
  ' This resets the LPT port
  OUT I2CHiPort,I2Csavedstatus
  OUT I2CLoPort,127
 END SUB
' ----------------------------
SUB I2Cdebugoff
  ' Turns off the I2C debugger
  CALL messg("ICee DISABLED ")
  I2Cdebug = 0
END SUB
' ----------------------------
SUB I2Cdebugon
  ' Turns the debugger on
  CALL messg("ICee ENABLED ")
  I2Cdebug = 1
END SUB
' ----------------------------
SUB I2Cgenstart
  ' transmits a start
  IF I2Cdebug = 1 THEN
     CALL messg("START")
  END IF
  '  start of transmission
  OUT I2CLoPort, 127
  delay hold
  OUT I2CHiPort, 8
  delay hold
  OUT I2CLoPort, 255
  delay hold
  OUT I2CLoPort, 255
  delay hold
  OUT I2CHiPort, 0
  delay hold
END SUB
' ----------------------------
SUB I2Cgenstop
  ' transmits a stop
  IF I2Cdebug = 1 THEN
     CALL messg("STOP")
  END IF
  OUT I2CLoPort, 255
  delay hold
  OUT I2CLoPort, 255
  delay hold
  OUT I2CHiPort, 8
  delay hold
  OUT I2CHiPort, 8
  delay hold
  OUT I2CLoPort, 127
  delay hold
END SUB
' ----------------------------
SUB I2Cgiveack
  ' Gives an ACK to a slave
  OUT I2CHiPort, 0
  delay hold
  OUT I2CLoPort, 255
  delay hold
  OUT I2CHiPort, 8
  delay hold
  OUT I2CHiPort, 0
  delay hold
  OUT I2CLoPort, 127
  delay hold
END SUB
' ----------------------------
SUB I2Cinit (timeout)
  ' aborts transmission and
  ' clears bus
  FOR I2Ca% = 0 TO 5
      OUT I2CLoPort, 255
      delay hold
      OUT I2CHiPort, 8
      delay hold
      OUT I2CLoPort, 127
      delay hold
      OUT I2CHiPort, 0
      delay hold
  NEXT I2Ca%
  I2Ctimeout = timeout
  OUT I2CHiPort, 8
  delay hold
END SUB
' ----------------------------
SUB I2Cmultiread (adr%, count%)
  ' performs a multiread
  adr% = (adr% OR 1)
  I2Cdevadr% = adr%
  CALL I2Cgenstart
  CALL I2Ctransmit(adr%)
  CALL I2Cwaitforack
  I2Cdevadr% = 0
  FOR i% = 0 TO count%
      CALL I2Creceive
      IF il% < count% THEN
      CALL I2Cgiveack
      END IF
      ICdta(il%) = I2Cresult%
  NEXT il%
  CALL I2Cgenstop
END SUB
' ----------------------------
SUB I2Copen (port%, dbug%)
  ' Always call this before
  ' any other routines !
  SELECT CASE port%
     CASE 0
       I2CLoPort = &H378
       I2Cmidport = &H379
       I2CHiPort = &H37A
     CASE 1
       I2CLoPort = &H278
       I2Cmidport = &H279
       I2CHiPort = &H27A
     CASE 2
       I2CLoPort = &H3BC
       I2Cmidport = &H3BD
       I2CHiPort = &H3BE
  END SELECT
  I2Csavedstatus = _
           INP(I2CHiPort)
  IF dbug% = 1 THEN
     I2Cdebug = 1
  ELSE
     I2Cdebug = 0
  END IF
END SUB
' ----------------------------
SUB I2Cpob
  ' puts bits on the bus
  IF SDA = 1 THEN
     OUT I2CLoPort, 127
     delay hold
  ELSE
     OUT I2CLoPort, 255
     delay hold
  END IF
  IF scl = 1 THEN
     OUT I2CHiPort, 8
     delay hold
  ELSE
     OUT I2CHiPort, 0
     delay hold
  END IF
  IF I2Cdebug = 1 THEN
  END IF
END SUB
' ----------------------------
FUNCTION I2Cread (adr%)
  ' reads a byte
  adr% = (adr% OR 1)
  I2Cdevadr% = adr%
  CALL I2Cgenstart
  CALL I2Ctransmit(adr%)
  CALL I2Cwaitforack
  I2Cdevadr% = 0
  CALL I2Creceive
  CALL I2Cgiveack
  CALL I2Cgenstop
  I2Cread = I2Cresult%
END FUNCTION
' ----------------------------
SUB I2Creceive
  ' receives a byte
  IF I2Cdebug = 1 THEN
     CALL messg("Receiving")
  END IF
  I2Cresult% = 0
  OUT I2CLoPort, 127
  delay hold
  FOR I2Ca% = 7 TO 0 STEP -1
      I2Cb% = 2 ^ I2Ca%
      OUT I2CHiPort, 8
      delay hold
      I2Cin% = _
      (INP(I2Cmidport) AND 128)
      OUT I2CHiPort, 0
      delay hold
      IF I2Cin% = 128 THEN
         I2Cresult% = _
            I2Cresult% + I2Cb%
         PRINT "1";
       ELSE
         PRINT "0";
      END IF
      IF I2Ca% = 4 THEN _
         PRINT " ";
  NEXT I2Ca%
  PRINT
END SUB
' ----------------------------
SUB I2Csettimeout (tme)
  ' assigns a timeout value
  I2Ctimeout = tme
END SUB
' ----------------------------
SUB I2Ctransmit (byte%)
  ' transmits a byte
  IF I2Cdebug = 1 THEN
     CALL messg("Transmitting")
  END IF
  I2Ca% = 0
  FOR I2Ca% = 7 TO 0 STEP -1
      I2Cb% = 2 ^ I2Ca%
      IF (byte% AND I2Cb%) =_
         I2Cb% THEN
         OUT I2CLoPort, 127
         delay hold
      ELSE
         OUT I2CLoPort, 255
         delay hold
      END IF
      OUT I2CHiPort, 8
      delay hold
      OUT I2CHiPort, 0
      delay hold
  NEXT I2Ca%
  OUT I2CLoPort, 127
  delay hold
END SUB
' ----------------------------
SUB I2Cwaitforack
  ' waits for slave acknowledge
  IF I2Cdebug = 1 THEN
     CALL messg("Wait for ACK")
  END IF
  OUT I2CLoPort, 127
  OUT I2CLoPort, 127
  delay hold
  OUT I2CHiPort, 8
  OUT I2CHiPort, 8
  delay hold
  acknowledge = 0
  acktimer = 0
  WHILE acknowledge = 0
   acktimer = acktimer + 1
   I2C.mon = _
    (INP(I2Cmidport) _
    AND 128)
   IF I2C.mon <> 128 THEN
    acknowledge = 1
   END IF
   IF acktimer = _
    I2Ctimeout THEN
    acknowledge = 1
    IF I2Cdevadr% <> 0 THEN
     IF I2Cdebug = 1 THEN
      CALL messg("No device")
      CALL holdsystem
     ELSE
      BEEP
     END IF
    ELSE
     IF I2Cdebug = 1 THEN
      CALL messg("No ACK")
      CALL holdsystem
     ELSE
      BEEP
     END IF
    END IF
   END IF
  WEND
  OUT I2CLoPort, 127
  OUT I2CLoPort, 127
  delay hold
  OUT I2CHiPort, 0
  OUT I2CHiPort, 0
  delay hold
END SUB
' ----------------------------
SUB I2Cwrite (adr%, dta%)
  ' writes a byte to a slave
  adr% = (adr% AND 254)
  I2Cdevadr% = adr%
  CALL I2Cgenstart
  CALL I2Ctransmit(adr%)
  CALL I2Cwaitforack
  I2Cdevadr% = 0
  CALL I2Ctransmit(dta%)
  CALL I2Cwaitforack
  CALL I2Cgenstop
END SUB
' ----------------------------
FUNCTION I2Cwwread _
  (adr%, sbadr%)
  adr% = (adr% OR 1)
  I2Cdevadr% = adr%
  CALL I2Cgenstart
  CALL I2Ctransmit(adr%)
  CALL I2Cwaitforack
  I2Cdevadr% = 0
  CALL I2Ctransmit(sbadr%)
  CALL I2Cwaitforack
  CALL I2Cgenstart
  adr% = adr% + 1
  CALL I2Ctransmit(adr%)
  CALL I2Creceive
  CALL I2Cgenstop
  I2Cwwread = I2Cresult%
END FUNCTION
' ----------------------------
  SUB I2Cwwsend _
      (adr%, sbadr%, dta%)
  ' writes with subadress
  adr% = (adr% AND 254)
  I2Cdevadr% = adr%
  CALL I2Cgenstart
  CALL I2Ctransmit(adr%)
  CALL I2Cwaitforack
  I2Cdevadr% = 0
  CALL I2Ctransmit(sbadr%)
  CALL I2Cwaitforack
  CALL I2Ctransmit(dta%)
  CALL I2Cwaitforack
  CALL I2Cgenstop
END SUB
' ----------------------------
SUB messg (dta$)
  ' shows the ICee messages
  PRINT dta$
END SUB
' ----------------------------

Back to Main Index

Legal Notes and Copyrights.

Standard Philips Copyright notice :

' Purchase of Philips I2c components conveys a licence under the Philips  I2C patent to use the components in the I2C system provided the system  conforms to the I2C specifications defined by Philips '
Back to Main Index

ACCESS bus.

One offspring of the I2C BUS is the ACCESS Bus. This bus was co-developed by Philips, Signetics, Digital and Intel.The goal was to create a bus that could help us getting rid of all cabling involved with computer peripherals. You would have 1 bus connector where you could hook up your keyboard,mouse,digitizer,scanner,printer,monitor etc.

Then by using sotware you could issue commands to your monitor or  printer.Things like selecting fonts or programming brightness and picture size could be done from within software on the host platform. Things like Hotplugging are included in the standard.There has been a chip developed that could replace the standard 8042 (which is the  keyboard controller in an ibm PC) by an access bus controller. Digital is using the bus in its Alpha based machines. Sony and some other manufacturers have monitors that support the remote programming  features.Microsoft will support the bus fully . (Windows 95).

Basically the hardware layer of the access bus is an I2C bus. All that has been done is implementing a software protocol to  provide additional functionality to the system.

This bus gas never gained any support due to the lack of performance. The idea was good but the speed was not available. Out of this idea the USB was developed. The basic mechanisms in I2C have been modified and taken to a new level. While the physical layer is different , the sync mechanisms , the handshaking , addressing , and multimaster mode is an improvement of the I2C bus.
Back to Main Index

I2C in your computer


You might not realise it but every motherboard using Pentium II and later processors has an I2C bus on board !. This bus is used for so called system management. This ranges from voltage detectors on the motherboard , temperature monitors in the CPU to the configuration paramteres for your memory. Todays DIMM memory modules have a small I2C EEPROM onboard that hold the timing information for the memory. This information is read during boot. The Slot One packaged processors have an I2C interface to read out the temperature of the CPU !.

In portable computers the bus is even more used. the little Trackball , TouchStick or Glidepoint all use I2C to transmit mouse coordinates !. Smart harddisk boast I2C buses. The Battery in a notebook can have an I2C bus that is used to read voltage , temperature and battery information. this bus is accessible via port &H80 in your computer. DO NOT MESS WITH IT !. If you have no clue how it works don't use it. Find documentation first. ! You can screw up the motherboard or other peripherals .
Back to Main Index

SOURCES OF INFORMATION ABOUT I2C


FTP sites

The following is a list of the various anonymous ftp sites that carry tools and examples about I2C and how to implement it. There are many others that  are not listed here that contains bits and pieces.  Usually you can find them using Archie and searching for "I2C","ACCESS BUS" and stuff like that.

ftp.funet.fi (nic.funet.fi)
/pub/compilers/8051
/pub/microprocs/MCS-51
ftp.oak.oakland.edu ai.uga.edu/pub/hardware ftp://ftp.inetbsystems.us.com/pub/Philips-MCU/bbs

Web pages

http://www.hut.fi/~iisakkil/stuff.html
http://www.ramtron.com
http://www.siemens.com
http://www.ping.be/electrozone

Back to Main Index

I2C products


This section includes descriptions and references to free and commercial software for the I2C Bus and lookalikes.FTP sites and BBSs contain many quality packages and code samples for free. For heavy duty use, you might prefer the many commercial packages that are available.With the public domain (or free) stuff, you're usually on your own. The commercial packages usually provide extensive documentation and support.

Free development tools

The following is a list of development tools that exist on the net.

IBM PC program to control I2C bus from the printer port.
Program: TV312.EXE  / TV400.EXE / I2CRAD.EXE
Description: Control program by Philips Semiconductors for I2C bus.
Location:  ftp.pppl.gov : /pub/8051/signetics-bbs
ftp.funet.fi : /pub/microprocs/MCS-51/signetics-bbs

The same site has lots of APP notes on i2C and how to implement it on 8051 and 68000 compatible CPU's.

Commercially available products

Philips Microcontroller Product Group
811 East Arques Ave. / POB 3409
Sunnvale, CA  94088-3409
Technical documentation:
Sunnyvale, CA - (800)447-1500  Fax: (408)991-3773
Eindhoven, Netherlands - Fax: 31-40-724825

A set of development boards for the I2C bus :

S87C00KSD  I2C evaluation Board
OM1016  I2C demo board with CPU and a number of peripherals like
I/O, AD/DA, LCD, RAM, EEprom, CLOCK, DTMF, IR receiver etc..
OM1018  Manual for the above.
OM1020  LCD and driver demoboard.
OM4151  Similar to OM1016 but without IR link.
OM4160  68070 based demoboard.
OM1022  I2C bus analyser. Hard and software for IBM PC.
Back to Main Index

I2C DOCUMENTATION

Periodicals that sometimes have articles about I2C

Various magazines and journals (journals seems to be THE popular name for magazines these days) provide articles from time to time on the I2C  bus

The Computer Applications Journal (Circuit Cellar Ink)
  - programming and construction articles
  - POB 7694, Riverton, NJ  08077-8784
  - FAX: (203)872-2204
  - Voice orders: (609)786-0409
  - On-line orders (BBS): (203)871-1988
  - Email orders: [email protected]

Electronic Engineering Times
  - industry announcements and trends
  - FREE to qualified engineers and managers involved in
  engineering decisions
  - Fulfillment Dept., PO Box 9055, Jericho, NY  11753-8955
  - FAX:  (516)733-6960

Electronics Now
  - construction articles
  - Box 55115, Boulder, CO  80321-5115
  - $19.97 one year

Elektor Electronics
  - programming and construction articles
  - World Wide Subscription Service Ltd
  Unit 4, Gibbs Reed Farm, Pashley Road
  Ticehurst TN5 7HE, England
  - 27 UK pounds
  or
  - Old Colony Sound Lab, P.O. Box 243, Peterborough, NH 03458
  - Tel. (603)924-6371, 924-6526
  - Fax: (603)924-9467
  - $57 USA and Canada per year
Back to Main Index

Books on I2C
I don't have information on all of these, only that they exist.  I would greatly appreciate it if someone could provide a short synopsis and the complete book name if you are familiar with any of these titles.

  Data book / Handbook / Users' Guide
  - Philips I2C devices Handbook
  - 8051 Handbook from philips (contains also complete I2C spec)
  pub no : 9397-750-00013
  - I2C peripherials for microcontrollers.
  98-8080-574 (Philips ord.nr)
  Currently depleted.Sheduled for reprint in august

  IC01  Semiconductors for Radio and Audio systems
  IC02  Semiconductors for TV and Video systems.
  IC03  Semiconductors for Telecom systems
  IC14  8048 based microcontrollers
  IC20  8051 based microcontrollers

  Le BUS I2C  (in FRENCH !!)
  By Dominique Paret
  Dunod Technique  ISBN 2-10-001717-9

  De I2C bus. ( in DUTCH )

  Published by Elektor from The netherlands
  Currently only available in Dutch. ENglish translation upcoming.
  ISBN .......

  Philips Data Sheet on the I2C Bus  * Free *
  Order # 98-8080-575-01

  by Mail
  Philips semiconductors  ! Philips Semiconductors
  811 East Arques Anenue  ! Literature distribution centre
  PO BOx3409  ! 1000 Business centre drive
  Sunnyvale California  94088-3409  ! Mount Prospect IL 60056

  Or by FAX  1-708-296-8556
  Phone 1-800-234-7381
Back to Main Index

Troubleshooting guide.

Right. So you have built your first system using the I2C bus and you find out that it doesn't work as it should. So what do we do now ? This section covers a few of the common pitfalls involved in using the bus.

First thing to check is : Are the pull-up resistors connected.?
Probably the most common error is that people forget to connect a pull-up resistor between SDA and VCC and SCL and VCC.  Remember : SDA and SCL are open collector or open-drain lines. Resistance value should be between 4K7 and 47K.

The longer you make your lines the lower the resistance value should be. This is to force more current into the lines to overcome the capacitance formed by the lines. (This is very important if you want to run on high speeds)

Check that the lines can be toggled between the logic levels. Check that the levels on both SDA and SCL fall into the allowed range. Check this both for high and low levels. Maybe there is a short circuit that straps one of the lines to VCC or GND.

By now you should have a bus that is capable of transporting I2C signals. Now you can try to send some information to a chip or read some information  It is best to connect only one slave device to the I2C bus.

The chip is not responding.

Check following things in order Are SCL and SDA connected correctly ? Are you accessing the right address ? Has the start command been issued correctly ?.

If you have a storage scope you can monitor the bus by connecting Channel 1 to SDA and channel 2 to SCL. Set the scope on Single shot  trigger on channel 2. Set pretrigger to1division. Or you can build the trigger circuit described in this FAQ under 'debugging tools'.

If you don't have a scope you can use another trick. Send the start command plus the slave address .Now make the SCL line
 high . Your Master is now waiting for ACK from the slave device. You can connect a led + resistor between VCC and SDA. If the led does not light then something is wrong.

Send a couple of stop commands and then try again.It is possible that the chip is locking up due to power-on effects. Replace the chip. It could be defective.

If here it still does not work you have a problem in the I2C protocol. Check that the START , ACQ and STOP sequences are correct. Also verify that the data transmitted is correct. MSB first.

When you got it talking you can connect the other devices one by one. Each time try to access them.

Sometimes I get strange results. Reading a device a couple of times ends up with different data all the time. Writing does not give predictable results. Sometimes the bus even locks up.

The most logic explanation here is that you have a problem with the bus signals. They are either not high enough or noisy. Or the capacitance on the bus might be so high that the edges of the signals become too slow. decrease the pull up resistance. ( start by connecting half of the value. ) This should improve the problem.

Another possibility is that you have 2 chips on the same address. This can happen. Example : You have a circuit that uses 2 PCF8574 I/O ports. In your hurry you forget to wire them for different addresses. (You can have up to 8 of these in your circuit)

Back to Main Index

Last Words ...

This FAQ compiles for a last time all i know about the I2C bus. Over time i got in touch with a lot of people , amongst them the people who designed the bus , people from Hewlett Packard , Synaptics and lots of other companies. I would like to extend greetings to those people. They had interesting problems and it was fun solving them. But the line has to stop somewhere.

I hope this FAQ may help someone out there.

Have a good life.
Vincent.