*******BIOC Agent 003's course in******
* *
* ========================== *
* =BASIC TELECOMMUNICATIONS= *
* ========================== *
* PART V *
***************************************
Revised: 08-AUG-84
PREFACE:
Previous installments of this series were focused on telephony from a Network
point-of-view. Part V wih,deal with telephone electronics focusing
primarily on the subscriber's telephone. Hereinafter simply referred to as
"fone."
Wiring:
-------
Assuming a standard one-line fone, there are usually 4 wires that lead out of
the fone set. These are standardly colored red, green, yellow, & black. The
red & green wires are the two that are actually hooked up to your CO. The
yellow wire is sometimes used to ring different fones on a party line (ie,
one #, several families--found primarily in rural areas where they pay less
for the service and they don't use the fone as much); otherwise, the yellow
is usually just ignored. On some two-line fones, the red & green wires are
used for the first fone # and the yellow & black are used for the second
line. In this case there must be an internal or external device that
switches between the two lines and provides a hold function. (Such as Radio
Shack's outrageously priced 2 line & hold module).
In telephony, the green & red wires are often referred to as tip (T) & ring
(R), respectively. The tip is the more positive of the two wires. This
naming goes back to the old operator cord boards where one of the wires was
the tip of the plug and the other was the ring (of the barrel).
A rotary fone (aka dial or pulse) will work fine regardless of whether the red
(or green) wire is connected the tip(+) or ring(-). A touch-tone (TM) fone is
a different story, though. It will not work except if the tip(+) is the green
wire. [Although, some of the more expensive DTMF fones do have a bridge
rectifier which compensates for polarity reversal.] This is why under
certain (non-digital) switching equipment you can reverse the red & green
wires on a touch-tone fone and receive free DTMF service. Even though it
won't break dial tone, reversing the wires on a rotary line on a digital
switch will cause the tones to be generated.
Voltages, Etc.
--------------
When your telephone is on-hook (ie, hung up) there is approximately 48 volts
of DC potential across the tip & ring. When the handset of a fone is lifted
a few switches close which cause a loop to be connected (known as the "local
loop") between your fone & the CO. Once this happens DC current is able to
flow through the fone with less resistance. This causes a relay to energize
which causes other CO equipment to realize that you want service.
Eventually, you should end up with a dial tone. This also causes the 48 VDC
to drop down into the vicinity of 12 volts. The resistance of the loop also
drops below the 2500 ohm level, though FCC licensed telephone equipment must
have an off-hook impedance of 600 ohms.
As of now, you ahands of our "friends" at D&B. To say the least, they were
n't exactly thrilled about it. In fact, they did not even believe that
they had a security problem! (Well, that just goes to prove that
if you are good, no one knows that you are there!)
In a big effort to defeat us, they called in an outside service
to spruce up their "security." Well, fortunately for u s, we were
able to find out about the new system! (Which wasn't really a problem.
First, they had the new dial-ups when you logged on, and as a lways they
have a nice little place on Telenet! ( Where we do most of our work: C
20188).
Now, they have set up a new system they like to call DunsNet. They are trying
to pass it off as a ectionately call this mute a black box.
The following are instructions on how to build a simple black box. Of course,
anything that prevents the voltage from dropping would work.
You only need two parts: A SPST toggle switch and a 10,000 ohm (10 K), 1/2
watt resistor. Any electronics store should stock these parts.
Now, cut 2 pieces of wire (about 6 inches long) and attach one end of each
wire to one of the terminals on the switch. Now turn your K500 (standard
desk fone) upside down and take off the cover. Locate wire (disconnect it
from its terminal). Now bring the switch out the rear of the fone and
replace the cover.
Put the switch in a position where you receive a dial tone> D5I-"!%M5R=M%Q%=9ruJU*J $SX9k the other side FREE.
When your phriends call (at a prearranged time), quickly lift & drop the
receiver as fast a possible. This will stop the ringing (do it again if it
doesn't) with out starting the billing. It is important that you do it
quickly (less than 1 second). Then put the switch in the FREE position and
pick up the fone. Keep all calls short and preferably under 15 minutes.
NOTE: If someone picks up an extension in the called parties house and
that fone is not set for FREE then billing will start.
NOTE: An old way of signalling a phriend that you are about to
call is making a collect call to a non-existent person in the
house. Since your friend will not accept the charges, he will
know that you are about to call and thus prepare the black box
(or visa versa).
WARNING: The Telco can detect black boxes if they suspect one on
your line. This is done due to the presence of AC voice
signal at the wrong DC level!
Pictorial Diagram:
(Standard Rotary K500 fone)
---------------------------------------
! !
***BLUE WIRE**>>F< !
! * * !
**WHITE WIRE** * !
! * !
! RESISTOR !
! * !
! * !
! >RR<*******SWITCH**** !
! * !
****GREEN WIRE********************** !
! !
---------------------------------------
NOTE: The Black Box will not work under ESS or other similar
digital switches since ESS does not connect the voice circuits
until the fone is picked up (& billing starts). Instead,
ESS uses an "artificial" computer generated ring.
Ringing:
--------
To inform a subscriber of an incoming call, the Telco sends 90 volts (PK) of
pulsing DC down the line (at around 15 to 60 Hz; usually 20 Hz). In most
fones this causes a metal armature to be attracted alternately between two
electro-magnets thus striking 2 bells. Of course, the standard bell (patented
in 1878 by Tom A. Watson) can be replaced by a more modern electronic bell or
signaling device.
Also, you can have lights and other similar devices in lieu of (or in
conjunction with) the bell. A simple neon light (with its corresponding
resistor) can simply be connected between the red & green wires (usually L1 &
L2 on the network box) so that it lights up on incoming calls.
WARNING: 90 VDC can give quite a shock. Exercise extreme
caution if you wish to further pursue these topics.
Also included in the ringing circuit is a capacitor tbig savings of time
since the hassle of using a a time shared public netwo rk does not exist.
We're sure that Mr. J.W.P. of DU NSPRINT had more on his mind when he wrote
the let ter (on the system)! DunsNet is accessible from a regular
dial-up. We have not been able to g et a number yet for this system,
but once on it allegedly works just like Telenet! Two carriage returns
and you will see "DunsNet" then the fa miliar "@" symbol. To use the
system like we showe d you, type "RPTS" at thiup to drop a trouble card for
long periods of ringing then a "no-no" detection device may be placed on the
line.
Incidentally, the term "ring trip" refers to the CO process involved to stop
the AC ringing signal when the calling fone goes off hook.
NOTE: It is suggested that you actually dissect fones to help
you better understand them. It will also help you to better
understand the concepts here if you actually prove them to
yourself. For example, actually take the voltage readings on
your fone line [any simple multi-tester (a must) will do.]
Phreaking is an interactive process not a passive one!
Dialing:
--------
On a standard fone, there are two common types of dialing: pulse & DTMF. Of
course, some people insist upon being different and do7ot use the DT thus
leaving them with MF (Multi Frequency, aka operator, blue box) tones. This is
another "no-no" and the Telco Security gentlemen have a special knack for
dealing with such "phreaks" on the network.
When you dial rotary, you are actually rapidly breaking & reconnecting
(breaking & making) the local loop once for each digit dialed. Since the
physical connection must be broken, you cannot dial if another extension (of
that #) is off-hook. Neither of the fones will be able to dial pulse unless
the other hangs up.
Another term often referred to in telephone electronics is the break ratio.
In the US, the standard is 10 pulses per second. When the circuit is opened
it is called the break interval. When it is closed it is called the make
interval. In the US, there is a 60 millisecond (ms) make period and a 40 ms
break period. (60+40=100 ms = 1/10 second). This is referred to as a 60%
make interval. Some of the more sophisticated electronic fones can switch
between a 60% & a 67% make interval. This is due to the fact that many
foreign nations use a 67% break interval.
Have you ever been in an office or a similar facility and saw a fone waiting
to be used for a free call but some asshole put a lock on it to prevent
outgoing calls?
Well, don't fret phellow phreaks, you can simulate pulse dialing by rapidly
depressing the switchhook. (If you depress it for longer than a second it
will be construed as a disconnect.) By rapidly switchooking you are causing
the local loop to be broken & made similar to rotary dialing! Thus if you
can manage to switchhook rapidly 10 times you can reach an operator to place
any call you want! This takes a lot of practice, though. You might want to
practice on your own fone dialing a friend's # or something else.
Incidentally, this method will also work with DTMF fones since all DTMF lines
can also handle rotary.
Another problem with pulse dialing is that it produces high-voltage spikes
that make loud clicks in the earpiece and cause the bell to "tinkle." If you
never noticed this then your fone has a special "anti-tinkle" & earpiece
shorting circuit (most do). If you have ever dissected a rotary fone (a must
for any serious phreak) you would have noticed that there are 2 sets of
contact that open and close during pulsing (on the back of the rotary dial
under the plastic cover). One of these actually opens and closes the loop
while the other mutes the earpiece by shorting it out. The second contacts
also activates a special anti-tinkle circuit that puts a 340 ohm resistor
across the ringing circuit which prevents the high voltage spikes from
interfering with the bell.
Dual Tone Multi Frequency (DTMF) is a modern day improvement on pulse dialing
in several ways. First of all, it is more convenient for the user since it
is faster and can be used for signaling after the call is completed (ie,
SCC's, computers, etc.). Also, it is more up to par with modern day
switching equipment (such as ESS) since pulse dialing was designed to
actually move relays by the number of digits dialed (in SxS offices).
Each key on a DTMF keypad produces 2 frequencies simultaneously (one from the
high group and another from the low group).
-------------------------
Low Group ! Q ! ABC ! DEF ! !
697 Hz-! 1 ! 2 ! 3 ! A !
! ! ! ! !
!-----!-----!-----!-----!
! GHI ! JKL ! MNO ! !
770 Hz-! 4 ! 5 ! 6 ! B !
! ! ! ! !
!-----!-----!-----!-----!
! PRS ! TUV ! WXY ! !
852 Hz-! 7 ! 8 ! 9 ! C !
! ! ! ! !
!-----!-----!-----!-----!
! ! OPER! ! !
941 Hz-! * ! 0 ! # ! D !
! ! Z ! ! !
!-----!-----!-----!-----!
1209 1336 1477 1633
(High Group--in Hz)
A portable DTMF keypad is known as a white box.
The fourth column (1633 Hz) is not normally found on regular fones but it does
have several special uses. For one, it is used to designate the prIo;ity of
calls on AUTOVON, the military fone network. These key are called: Flash,
Immediate, Priority, & Routine (with variations) instead of ABCD. Secondly,
these keys are used for testing purposes by the Telco. In some area you can
find loops as well as other neat tests (see Part II) on the 555-1212
directory assistance exchange. For this, you would call up an DA in certain
areas [that have an Automatic Call Distributor (ACD)] and hold down the "D"
key which should blow the operator off. You will then hear a pulsing dial
tone which indicates that you are in the ACD internal testing mode. You can
get on one side of a loop by dialing a 6. The other side is 7. Some phreaks
claim that if the person on side 6 hangs up, occasionally the equipment will
screw up and start directing directory assistance calls to the other side of
the loop. Another alleged test is called REMOB which allows you to tap into
lines by entering a special code followed by the 7 digit number you want to
monitor. Then there is the possibility of mass conferencing.
ACD's are become rare though. You will probably have to make several NPA-555-
1212 calls before you find one.
You can modify regular fones quite readily so that they have a switch to
change between the 3rd and 4th columns. This is called a silver box (aka grey
box) and plans can be found in Tap as well as on many BBS's.
Transmitter/Receiver:
---------------------
When you talk into the transmitter, the sound waves from your voice cause a
diaphragm to vibrate and press against the carbon granules (or another
similar substance). This causes the carbon granules to compress and contract
thus changing the resistance of the DC coupled path through it. Therefore,
your AC voice signal is superimposed over the DC current of the local loop.
The receiver works in a similar fashion where the simple types utilize a
magnet, armature, & diaphragm.
Hybrid/Induction Coil:
----------------------
As you may have noticed, there are two wires for the receiver and two for the
transmitter in the fone, yet the local loop consists of 2 wires instead of 4.
This 4-wire to 2-wire conversion is done inside the fone by a device known as
an induction coil which uses coupling transformers. All of the internal
Telco trunks also use 4 wires. It is only the local loop that uses 2 since it
is cheaper. A device in the CO known as a hybrid converts between 4 and 2
wire set-ups similar to the induction coil inside the fone. Special data
transmission lines require extremely low signal to noise ratios, they require
the full four wires--two for transmission and two for receiving (even on the
local loop).
Miscellaneous:
--------------
In the telephone, there is also a balancing network consisting of a few
capacitors & resistors which provide sidetone. Sidetone allows the caller to
hear his own volume in the receiver. He can then adjust his voice
accordingly. This prevents people from shouting or speaking too softly
without noticing it.
Hold:
When a telephone goes off hook, the resistance drops below 2500 ohms. At this
point, the Telco will send a dial tone. To put someone on hold you must put
a 1000 ohm resistor (1 watt) across the Tip & Ring before it reaches the
switchhook. In this way, when the fone is hung up (for hold) the resistance
remains below 2500 ohms which causes the CO to believe that you are still
off-hook. You can build a simple hold device using the following pictorial
diagram:
/
(RED) O-------------------------/
[L1] ! ! !
! ! !
1000 Ohm ! !
Resistor Ringing !
! Circuit !
! ! !
/ ! Switch-
/ SPST Switch ! Hook
! ! !
! ! !
! ! !/
(GREEN) O------------------------/
[L2]
--> To Rest of
Fone
This hold devicw is only effective if you also hang up the fone. To make a
hold/mute switch, simple connect a wire in place of the 1K resistor to effect
a short circuit (who cares if you damage CO equipment?).
Conclusion:
-----------
NOTE: Many of the electronics components of normal fones
(K500) are enclosed in the network box (which shouldn't
be opened).
I have assumed that the reader has a basic knowledge of electronics. Also, I
have assumed that you have read the 4 previous installments of this series
(and hopefully enjoyed them).
In part VI, we will take a look at fortress fones.
Suggested Further Reading:
--------------------------
Electronics Courses A-D, TAP, @ $.75 each.
Electronic Telephone Projects, A.J. Caristi, Howard Sams Books.
Everything you Always Wanted to Know About 1633 Hz Tones but Were Afraid to
Ask, The Magician, TAP, issue #62.
Free BELL phone calls, TAP, Fact sheet #2, @ $.50.
Free GTE phone calls, TAP, Fact sheet #3, @ $.50.
How to modify your Bell Touch Tone Fone to Have 1633 Cycle Tones, TAP,
Issue #63.
Modifying Your Phone For 1633 Hz (new electronic keypads), Fred Steinbeck,
TAP, issue #84.
Notes on the Network, AT&T.
The Phone Book, J. Edgar Hyde.
Regulating The Telephone Company In Your Home, Ramapart Magazine, June 1972.
REMOBS, TAP #91 (not yet published as of this writing).
Understanding Telephone Electronics, Texas Instruments.
Acknowledgement: Big Brother for his technical critique.
& other assorted sources...
TAP/Room 603/147 W 42 St./New York, NY 10036. Please specify by backissue #'s
(not article names). All back - issues are $1 each. Subscriptions are
$10/year (10 issues). Say that BIOC Agent 003 sent you.
Another good phreak publication:
2600/Box 752/Middle Island, NY 11953.
Subscriptions are $10/year. Backissues are $1 each.
Excelsior,
*****BIOC (P) 1984 BIOC
*=$=*Agent International
*****003
July 18, 1984
<<=-FARGO 4A-=>>
Knights of Shadow
[RACS III - xxx/xxx-xxxx]
[Sherwood Forest ][ - xxx/xxx-xxxx]
PS Sysops of other BBS's are welcome to use this phile on their board
providing none of the information is altered.